Hi all,
I am going along the lines of a standard Indian 200 barrel, a Scootopia clubman and a standard carb with the elbow and a filter(not breathsweet) on top. Running with no panels.
In the article Darrell states that he ends up jetting with a 55 pilot and a 175 main. Where do I get a 175 main as all usual places seem to only stock up to a 140.
Can anyone advise?
Thanks
John
Bang for Buck Feature
- Eibar-Jet200
- registered user
- Posts: 12
- Joined: Fri Jul 16, 2010 7:58 pm
- Main scooter: Serveta Jet 200
- Location: West Lothian
- Contact:
- Doom Patrol
- registered user
- Posts: 1823
- Joined: Wed Jan 07, 2009 5:03 pm
- Main scooter: Jet 200
- Location: Second star on the right and straight on till morning
- Contact:
Sounds like you might have to get one drilled out if that is the case.
-
- registered user
- Posts: 1741
- Joined: Wed Jan 07, 2009 8:42 am
- Main scooter: Lambretta TV175 S3- what else!
- Location: Bali-Hai bar, Locarno Ballroom Bristol, 1967!- mines a Brown Split!!
- Contact:
not disputing the fact at all but 175 does seem mighty big on a "standard" carb. Not a mistype?
Chris
Chris
Scootering since 1968.
- Eibar-Jet200
- registered user
- Posts: 12
- Joined: Fri Jul 16, 2010 7:58 pm
- Main scooter: Serveta Jet 200
- Location: West Lothian
- Contact:
No I went in and rechecked the article. Definitely a 175! Yes I though rather large too, but I found them on Readspeed site.
Darrell may come on and confirm the size.
Thanks
John
Darrell may come on and confirm the size.
Thanks
John
-
- registered user
- Posts: 1693
- Joined: Tue Jan 31, 2012 8:54 pm
- Main scooter: Lambretta GP
- Contact:
I asked the same question, as I had my doubts, and it was confirmed as a 175. Eurocarb (Dellorto importer in Reading) have genuine jets in the full range, up to 175 and beyond.
Adam
Adam
- Eibar-Jet200
- registered user
- Posts: 12
- Joined: Fri Jul 16, 2010 7:58 pm
- Main scooter: Serveta Jet 200
- Location: West Lothian
- Contact:
Thanks all.
I have placed an order with Readspeed, I will call them in the morning to check it is in stock.
175 is huge compared to standard, but if that is what it needs then fine.
This is for my EuroLam bike so I need it to get there and back.
George, if I have no success then I will drop you a pm. appreciated.
John
I have placed an order with Readspeed, I will call them in the morning to check it is in stock.
175 is huge compared to standard, but if that is what it needs then fine.
This is for my EuroLam bike so I need it to get there and back.
George, if I have no success then I will drop you a pm. appreciated.
John
- HxPaul
- registered user
- Posts: 1110
- Joined: Fri Dec 06, 2013 1:58 pm
- Main scooter: lambretta Li 150
- Location: Halifax,Yorkshire
- Contact:
I run a Casa 210 top end on a big block engine case.I use an Ancillotti type exhaust from scootopia and a 22mm scootopia carb,I have a 48 pilot jet and a 135 main jet in the carb,it all runs through a standard airbox with a standard filter eliment fitted and it runs on the rich side.I dont think it would even start with a 55 pilot and a 175 main jet.
-
- registered user
- Posts: 1741
- Joined: Wed Jan 07, 2009 8:42 am
- Main scooter: Lambretta TV175 S3- what else!
- Location: Bali-Hai bar, Locarno Ballroom Bristol, 1967!- mines a Brown Split!!
- Contact:
my monies on a 125 size.
Scootering since 1968.
drill bit 1.75mm !! spend some more money and get these http://www.baumtools.com/shop/fuel-inje ... Opa6jnTWhA
C’est la vie