What colour is the frame ? Looks pale blue in first photo then grey or white in others ??
As was said in previous post . cant believe no one knocked about that. or nicked it . must of been out of sight.
26 years later
-
Boothy_the_makem
- registered user
- Posts: 193
- Joined: Wed Dec 28, 2011 10:15 pm
- Playstation gamer tag: Phantomkiller_uk
- Main scooter: modded t5 classic wi a parker
- Contact:
Nice one mate. bet you wont leave that out in the garden again
What colour is the frame ? Looks pale blue in first photo then grey or white in others ??
As was said in previous post . cant believe no one knocked about that. or nicked it . must of been out of sight.
What colour is the frame ? Looks pale blue in first photo then grey or white in others ??
As was said in previous post . cant believe no one knocked about that. or nicked it . must of been out of sight.
Canny lass, Geordie girl, he gave her pints and fags and grub and shorts. Canny lass, Geordie girl, she gave him earache and penal warts,Penal warts.
-
Devlam
- registered user
- Posts: 90
- Joined: Tue Mar 15, 2011 8:48 pm
- Main scooter: Lambretta Li150 Special
- Contact:
Its a pale green. I couldn't make up my mind on colour so I got some tester pots out of B&Q mixed em around until I got something I liked, brushed it on a spare horn cast I had, sprayed it over with lacquer and then the guy who painted it got it matched. I like the result and I doubt I'll see the same colour anywhere?
-
Boothy_the_makem
- registered user
- Posts: 193
- Joined: Wed Dec 28, 2011 10:15 pm
- Playstation gamer tag: Phantomkiller_uk
- Main scooter: modded t5 classic wi a parker
- Contact:
Be nice to see it finished. looking good up to now 
Canny lass, Geordie girl, he gave her pints and fags and grub and shorts. Canny lass, Geordie girl, she gave him earache and penal warts,Penal warts.
-
stuckintheeighties
- registered user
- Posts: 14
- Joined: Tue Jan 17, 2012 9:18 pm
- Main scooter: SX200
- Contact:
Looking really good.
Just a question about the three hole engine mounts- I was lead to believe these are mounted with the bottom hole at 6 o'clock? Sure I read that somewhere?
Just a question about the three hole engine mounts- I was lead to believe these are mounted with the bottom hole at 6 o'clock? Sure I read that somewhere?
-
Devlam
- registered user
- Posts: 90
- Joined: Tue Mar 15, 2011 8:48 pm
- Main scooter: Lambretta Li150 Special
- Contact:
stuckintheeighties wrote:Looking really good.
Just a question about the three hole engine mounts- I was lead to believe these are mounted with the bottom hole at 6 o'clock? Sure I read that somewhere?
Hmmmm.. I should have come back to this sooner. Occupied with other things.
From what I read you're right. Camlam put these in for me!
How much of a problem is this. On the flywheel side I would say the middle hole is putting slightly higher than straight ahead. On the other side the middle hole is pointing straight forward.
-
wrecklessrobbie
- registered user
- Posts: 394
- Joined: Thu Jan 09, 2014 7:34 pm
- Main scooter: li150
- Location: York
- Contact:
Did I notice your fork tube bump stop had broken off when fitting the forks.
I have recently stripped my s2. The tube stop fell out. I had to weld it back on.
I don't think you can pass an MOT without a bump stop. Have you rewelded it?
Robbie
I have recently stripped my s2. The tube stop fell out. I had to weld it back on.
I don't think you can pass an MOT without a bump stop. Have you rewelded it?
Robbie
-
Devlam
- registered user
- Posts: 90
- Joined: Tue Mar 15, 2011 8:48 pm
- Main scooter: Lambretta Li150 Special
- Contact:
Cheers Robbie -- It's fixed but I didn't want to weld because it had all been painted. I fixed it in place with JB weld, then drilled and tapped it. Put a couple of bolts in then remove as much metal as I could - then touched up. It looked Ok, but is now hidden anyway. So all good.
-
wrecklessrobbie
- registered user
- Posts: 394
- Joined: Thu Jan 09, 2014 7:34 pm
- Main scooter: li150
- Location: York
- Contact:
Ah that's good.
The scooter looks fantastic.
Some hard work and effort gone into it.
I have a big pile of stripped down s2 eibar.
Am now working on doing a kind of restoration. If it turns out half as good as yours I will be happy
The scooter looks fantastic.
Some hard work and effort gone into it.
I have a big pile of stripped down s2 eibar.
Am now working on doing a kind of restoration. If it turns out half as good as yours I will be happy