Got a 42 mm clubman at the mo on my S2, but I'd like a bit more ooommph, without cutting rear board. Its been dynoed at 75 but as we all know thats not a true reflection of road speed. I've got a spanish 150 gearbox. Ideally I'm looking at a general allrounder of a pipe.
cheers.
Best exhaust for Stg 4 barrel, 28mm delly?
-
soosh
- registered user
- Posts: 1106
- Joined: Sun May 03, 2009 2:01 pm
- Main scooter: GP RS200 Iron barrel
- Contact:
If you don't want to cut the rear board then maybe a jl3 curley?
Three pipes I've used are Taff, jl3 and a PM. Good spread of power and will pull 4.8 well 1 or 2up but unfortunately you will need slight trimming on those but worth it.
Three pipes I've used are Taff, jl3 and a PM. Good spread of power and will pull 4.8 well 1 or 2up but unfortunately you will need slight trimming on those but worth it.
-
Spanish Fly
- registered user
- Posts: 198
- Joined: Tue Nov 30, 2010 1:23 pm
- Main scooter: P200e
- Contact:
Stage 2 specific pipe:a.j wrote:Got a 42 mm clubman at the mo on my S2, but I'd like a bit more ooommph, without cutting rear board. Its been dynoed at 75 but as we all know thats not a true reflection of road speed. I've got a spanish 150 gearbox. Ideally I'm looking at a general allrounder of a pipe.
cheers.
http://www.ekmpowershop12.com/ekmps/sho ... 1308-p.asp
-
Beanhead
- registered user
- Posts: 56
- Joined: Fri Dec 23, 2011 1:37 pm
- Main scooter: 1970 Lambretta gp
- Location: Manchester
- Contact:
just a note on the curly, i had one on a 225 mugello and it was poo!! grounding issues too, some better pipes out there than one of those.
Facebook - Lee Bardsley
Vesperados S.C
Sent from my PC using My Fingers
Vesperados S.C
Sent from my PC using My Fingers
-
col68
- registered user
- Posts: 118
- Joined: Sun Oct 30, 2011 9:36 am
- Main scooter: lambretta s2 li225 ts1
- Location: Spalding,lincolnshire
- Contact:
if you dont want to brake the bank what about a fresco pipe got one on my small bloke gse 200 sil stage 4 with a 30mm phbh, pulls very well from low to 5000 in 4th running in at the moment .
:fb:
I've got a similar set up but am looking at the new BGM MB Clubman or if I can't wait any longer the Gori. I don't like the look of those motorbike type exhausts.
col68 wrote:if you dont want to brake the bank what about a fresco pipe got one on my small bloke gse 200 sil stage 4 with a 30mm phbh, pulls very well from low to 5000 in 4th running in at the moment .:fb:
Same kit as me, and I'm running in too. I was thinking of going down the fresco route, is yours under kickstart?
Yeah they're not very good I know. Its what I had at the time.
-
col68
- registered user
- Posts: 118
- Joined: Sun Oct 30, 2011 9:36 am
- Main scooter: lambretta s2 li225 ts1
- Location: Spalding,lincolnshire
- Contact:
now mate mine is over kick start fresco end can had come off my pipe so i had a scorpion end can and short pipe in stainless steel looks nice :anbrgin; made 1 good pipe out of 2 . 
