Page 1 of 1
RB20 + LTH/Jimmers manifold
Posted: Thu Sep 11, 2014 10:22 pm
by ArKaTxU
Hi.
RB20 + this manifold and PHBH30 fits under sidepanel in a jet200?
Thanks!
Re: RB20 + LTH/Jimmers manifold
Posted: Fri Sep 12, 2014 12:13 am
by coaster
ArKaTxU wrote:Hi.
RB20 + this manifold and PHBH30 fits under sidepanel in a jet200?
Thanks!
I cannot be certain with an RB but I'm using an LTH short manifold on a TS1 and it fits under an LiS slimstyle panel with a GP or Breathsweet elbow and remote filter BUT I am using a BGM PWK 30mm carb which is about 20mm shorter than a PHBH. The Mikuni is another short option.
Re: RB20 + LTH/Jimmers manifold
Posted: Fri Sep 12, 2014 7:48 am
by jonashford
i use a rb lth manifold with a tmx 35 on sx panels there is loads of room, but there was plenty with the std manifold as well
Re: RB20 + LTH/Jimmers manifold
Posted: Fri Sep 12, 2014 9:10 am
by ArKaTxU
coaster wrote:ArKaTxU wrote:Hi.
RB20 + this manifold and PHBH30 fits under sidepanel in a jet200?
Thanks!
I cannot be certain with an RB but I'm using an LTH short manifold on a TS1 and it fits under an LiS slimstyle panel with a GP or Breathsweet elbow and remote filter BUT I am using a BGM PWK 30mm carb which is about 20mm shorter than a PHBH. The Mikuni is another short option.
In ScooterCenter catalog they say that BGM PWK 28/30 have 85mm and PHBH 90mm. Its correct? Because if BGM PWK 28 have 70mm I think that is a good option too.
jonashford wrote:i use a rb lth manifold with a tmx 35 on sx panels there is loads of room, but there was plenty with the std manifold as well
Yes, I have used TMX35 but I want something smaller this time.
Thanks!
Re: RB20 + LTH/Jimmers manifold
Posted: Fri Sep 12, 2014 7:30 pm
by coaster
ArKaTxU wrote:[.....In ScooterCenter catalog they say that BGM PWK 28/30 have 85mm and PHBH 90mm. Its correct? Because if BGM PWK 28 have 70mm I think that is a good option too.
I'll measure a PWK and a PHBH for you when I get up to Norfolk in an hour or so just to make sure
Re: RB20 + LTH/Jimmers manifold
Posted: Sat Sep 13, 2014 12:06 am
by ArKaTxU
Thanks!
Re: RB20 + LTH/Jimmers manifold
Posted: Sat Sep 13, 2014 12:16 am
by coaster
coaster wrote:ArKaTxU wrote:[.....In ScooterCenter catalog they say that BGM PWK 28/30 have 85mm and PHBH 90mm. Its correct? Because if BGM PWK 28 have 70mm I think that is a good option too.
I'll measure a PWK and a PHBH for you when I get up to Norfolk in an hour or so just to make sure
PWK measures 83mm
PHBH bare measures 90mm
PHBH with plastic bell mouth measures 97mm
I was a bit out with my previous guesstimate
Re: RB20 + LTH/Jimmers manifold
Posted: Sat Sep 13, 2014 12:36 am
by ArKaTxU
no problem
Thanks