Have an RB engine and think it would be more sensible running with air filter but am no clearer to knowing what fits with reading various threads. Does the Breath Sweeter fit and I have also seen it lying horizontal , does it work ok like this?
Also oil seal has gone after 400 miles on brand new engine, anything I should look out for on changing it that might point to why it lasted so few miles (not too experienced on lammy engines but gonna give it a go).
thanks
Mikini TMX 35mm - what air filter fits with long range tank?
-
Fenian Mick
- registered user
- Posts: 64
- Joined: Thu Dec 10, 2009 10:41 am
- Contact:
In my experience most mid/long range usually accommodate the carb its the panel clearance for the filter which is going to be your main problem.
The standard Af RB manifold takes the Mikuni plus filter too close too the panel to give a good flow of air.
I have used a breath sweet facing backwards with a steel tube support (squashed narrow) inside the join between filter and air hose to prevent the hose becoming squashed and the jubilee clips coming undone, however this only fitted with the LTH short manifold and then had to down jet due to the air restriction and lost some power all for the sake of NOT cutting a panel hole.
The standard Af RB manifold takes the Mikuni plus filter too close too the panel to give a good flow of air.
I have used a breath sweet facing backwards with a steel tube support (squashed narrow) inside the join between filter and air hose to prevent the hose becoming squashed and the jubilee clips coming undone, however this only fitted with the LTH short manifold and then had to down jet due to the air restriction and lost some power all for the sake of NOT cutting a panel hole.
- Andy Pickering
- registered user
- Posts: 2172
- Joined: Sun Jan 25, 2009 10:15 pm
- Main scooter: GP
- Location: Hull
- Contact:
Eden runs with a filter and long range tank with his TMX or used to anyway..their is a piccy somewhere..
Ricspeed, gone but never forgotten RIP my friend #59
-
WINTERMODEL150
- registered user
- Posts: 436
- Joined: Sun Oct 17, 2010 5:31 pm
- Main scooter: lambretta ld auto
- Contact:
Just fitted an LTH right angled filter to my Ts1 (gp body work) using a short MB inlet and it rubs on the inside of the panel badly
,anyway I have now put a bulge in the side panel to gain clearance but not sure what looks worse a hole or the bulge iv'e now created ,still atleast the motors now protected from the rain,unlike my LD auto that sucked up most of the rain from the M5 yesterday on the way back from wooly.
On the other hand if you've got a series 1/2 then you should have more than enough clearance to run an LTH filter.
As for seals I use Rolf or MB seals.
Dean
On the other hand if you've got a series 1/2 then you should have more than enough clearance to run an LTH filter.
As for seals I use Rolf or MB seals.
Dean
-
Timbo
- registered user
- Posts: 1276
- Joined: Tue Mar 03, 2009 2:46 pm
- Main scooter: SX200 and GP230 RT
- Location: Luton area.....
- Contact:
Any idea where that remote can be purchased..eden wrote:
on the right side as apposed to the wrong side it works like this, I'm not sure it would work on the wrong side with an RB or TS though, maybe some one can enlighten me
-
WINTERMODEL150
- registered user
- Posts: 436
- Joined: Sun Oct 17, 2010 5:31 pm
- Main scooter: lambretta ld auto
- Contact:
Andy Francis has them in stock £35Timbo wrote:Any idea where that remote can be purchased..eden wrote:
on the right side as apposed to the wrong side it works like this, I'm not sure it would work on the wrong side with an RB or TS though, maybe some one can enlighten me
Dean
-
rosscla
- registered user
- Posts: 4823
- Joined: Tue Oct 25, 2011 9:50 pm
- Main scooter: Lambretta
- Location: Lanarkshire
- Contact:
Buy the silicon hose and filter from fleabay and a couple of jubilee clips and bob's the relative of you choice
"Our dilemma is that we hate change and love it at the same time; what we really want is for things to remain the same but get better."

