Search found 163 matches
- Sat Nov 21, 2015 3:54 am
- Forum: Paint & Bodywork Tech
- Topic: lambretta frame jig work
- Replies: 12
- Views: 13319
Re: lambretta frame jig work
Yes please! That would be great.
- Thu Nov 12, 2015 9:48 pm
- Forum: Paint & Bodywork Tech
- Topic: lambretta frame jig work
- Replies: 12
- Views: 13319
Re: lambretta frame jig work
Do you have any rough dimensions for series 1/2 frames? I have to replace the centre stand strut on my ser 2 and my legshields are a bit wavy yet to try and sort it that way. I'd rather some kind of dimensions. I'm a welder fitter by trade amd set in my ways!! Lots of info out there for ser 3 but no...
- Tue Jun 11, 2013 1:04 pm
- Forum: Lambretta Tech
- Topic: Reverse pull on ser 1/2?
- Replies: 2
- Views: 1936
Re: Reverse pull on ser 1/2?
It looks like it will really rub on the cable.
- Tue Jun 11, 2013 1:42 am
- Forum: Lambretta Tech
- Topic: Reverse pull on ser 1/2?
- Replies: 2
- Views: 1936
Reverse pull on ser 1/2?
First off I have never had a disc brake for a lambretta before and I'd like to set it up with reverse pull. I see instructions on how to do it all over the web but they are always ser 3! It looks like the inner fender would be a problem, am I wrong? Has this been done and how should I do it?
Thanks
Thanks
- Fri May 17, 2013 1:12 pm
- Forum: Lambretta Tech
- Topic: Varitronic vs BGM regulator, what's the difference?
- Replies: 10
- Views: 6305
Re: Varitronic vs BGM regulator, what's the difference?
Wired it up, and fired it up last night. Works great! Thanks 
- Thu May 16, 2013 10:54 am
- Forum: Lambretta Tech
- Topic: Varitronic vs BGM regulator, what's the difference?
- Replies: 10
- Views: 6305
Re: Varitronic vs BGM regulator, what's the difference?
Ok, haha that's what I was considering "inline"! Maybe I'm not so bad at this!!! 
Thanks
Thanks
- Thu May 16, 2013 10:15 am
- Forum: Lambretta Tech
- Topic: Varitronic vs BGM regulator, what's the difference?
- Replies: 10
- Views: 6305
Re: Varitronic vs BGM regulator, what's the difference?
So, a wire from reg to positive on the cap, to the speedo? And then just a ground wire from the neg on the cap to the chassis?
- Wed May 15, 2013 10:03 pm
- Forum: Lambretta Tech
- Topic: Varitronic vs BGM regulator, what's the difference?
- Replies: 10
- Views: 6305
Re: Varitronic vs BGM regulator, what's the difference?
Ok, so how do I wire in the capacitor? I'm not good with electrical. So it has to be run paralel. How do I do that?
Thanks
Thanks
- Wed May 15, 2013 2:32 am
- Forum: Lambretta Tech
- Topic: Varitronic vs BGM regulator, what's the difference?
- Replies: 10
- Views: 6305
Re: Varitronic vs BGM regulator, what's the difference?
Great, thanks. I would rather keep it as is and not mess with it, the vari reg stays then. As for the capacitor I'm not sure I need it. I'm going to try without for now and if I decide later I need it then I'll hook it up.
Cheers
Cheers
- Tue May 14, 2013 2:53 am
- Forum: Lambretta Tech
- Topic: Varitronic vs BGM regulator, what's the difference?
- Replies: 10
- Views: 6305
Varitronic vs BGM regulator, what's the difference?
I run a varitronic ignition kit on my ser 1, I'm now hooking up my Speedhut GPS speedo (has to be run DC). I have a BGM regulator as a spare and am wondering which is best to use. So, my varitronic kit is running AC without a battery and is a very early test version of the kit. Whereas the BGM is a ...