Looking to refurb my MMW/LTH master cylinder, can see kits for £67 but I only want the seals,
anyone know what they're off?
Search found 45 matches
- Sat Nov 02, 2024 6:00 pm
- Forum: Lambretta Tech
- Topic: MMW/LTH master cylinder seals
- Replies: 1
- Views: 2466
- Tue Jan 21, 2020 10:04 pm
- Forum: Standard Scoots & Restorations
- Topic: GS 160 Parts - Best Online Dealer?
- Replies: 3
- Views: 10077
Re: GS 160 Parts - Best Online Dealer?
Try Dez at this site
http://www.discodezscooters.co.uk/
Message him and he'll get back to you, he lived in NZ for a while a few years back.
http://www.discodezscooters.co.uk/
Message him and he'll get back to you, he lived in NZ for a while a few years back.
- Thu Jan 02, 2020 10:25 pm
- Forum: Lambretta Tech
- Topic: S1 Hidden Master Cylinder - Where & How
- Replies: 4
- Views: 3419
Re: S1 Hidden Master Cylinder - Where & How
You can just squeeze one in if you make your own brackets.
- Thu Oct 29, 2015 7:39 pm
- Forum: Lambretta Tech
- Topic: 6v BGM Stator
- Replies: 1
- Views: 1526
6v BGM Stator
One for the electrical boffins.
I want to loose the points on my series one, but would like to keep the 6volt lighting system.
Can I just swap the 12v lighting coils for 6v and wire them up the same on the stator?
Will the original 6v rectifier designed for a 4 pole stator cope with the output?
I want to loose the points on my series one, but would like to keep the 6volt lighting system.
Can I just swap the 12v lighting coils for 6v and wire them up the same on the stator?
Will the original 6v rectifier designed for a 4 pole stator cope with the output?
- Sun May 10, 2015 9:50 am
- Forum: General Scooter Chat
- Topic: Road tax
- Replies: 7
- Views: 3439
Re: Road tax
Just swapped my SX over to historic vehicle tax from standard as it was due, was expecting all kinds of problems now the local VRO offices are shut. Local post office didn't want to know, (don't think they understood the concept of doing something for which no money was going in their till). Went to...
- Thu May 07, 2015 9:31 am
- Forum: Lambretta Tech
- Topic: flywheel jammed
- Replies: 18
- Views: 8226
Re: flywheel jammed
Don't be so hasty Graham , I'm sure we can lap that out!
- Mon May 04, 2015 9:36 pm
- Forum: Lambretta Tech
- Topic: Hidden master cylinder
- Replies: 3
- Views: 2458
Re: Hidden master cylinder
Made three simple brackets for my series 1 , two threaded lugs welded to the frame to mount the cylinder and a bracket to hold the adjuster. Took a bit of jiggling/shaving but got it to fit with the horn still in its original place. Stupidly forgot to allow for the banjo once fitted , hence the hole...
- Sun Jun 16, 2013 9:18 pm
- Forum: Lambretta Tech
- Topic: End can padding
- Replies: 3
- Views: 2125
Re: End can padding
Cheers for the reply, did it make a big difference to the noise levels?
- Sun Jun 16, 2013 8:46 pm
- Forum: Lambretta Tech
- Topic: End can padding
- Replies: 3
- Views: 2125
End can padding
I need to re-pack the wadding in my expansions end can, has anyone had experience of doing this,
is there any type of padding better than others/recommended?
Please share.
is there any type of padding better than others/recommended?
Please share.
- Tue Jan 22, 2013 5:48 pm
- Forum: Lambretta Tech
- Topic: 25mm /200 jetting
- Replies: 3
- Views: 2454
Re: 25mm /200 jetting
Hi Graham, carb settings as dynoed at Diablo for my 200 lump curently powering the rustmobile. Should think the rapido is not much different to the SIL stg 4. Rapido Classic 200 Std SX200 Gearing AF Clubman Carb 25mm PHBL Dellorto Main 95 Needle D26 Slide 40 Atomiser AQ268 Pilot 50 Choke 60 Pilot Sc...