Search found 8 matches
- Sat Jul 28, 2012 3:58 pm
- Forum: Lambretta Tech
- Topic: SIP Lambretta Digital Speedo
- Replies: 313
- Views: 147022
Re: SIP Lambretta Digital Speedo
Managed to figure it out, it was the sequence of seeding it up that I was unsure about, got most the settings from here. Cheers.
- Sat Jul 28, 2012 2:57 pm
- Forum: Lambretta Tech
- Topic: SIP Lambretta Digital Speedo
- Replies: 313
- Views: 147022
Re: SIP Lambretta Digital Speedo
Can someone help me please, lost instructions for the speedo, can some one post up an idiots guide on how to adjust the settings please. Everything is working on it but I need to calibrate it for mph, time, wheel size etc. Cheers.
- Fri Jun 08, 2012 11:48 pm
- Forum: Lambretta Tech
- Topic: Ron Moss - Avanti TT3 - Cylinder Kit - Review & Test.....
- Replies: 750
- Views: 299013
Re: Ron Moss - Avanti TT3 - Cylinder Kit - Review & Test....
Everything is fitted and it is timed up and running. The pwk has a jjh needle on the middle clip and it's jetted with the biggest jets I have, 48 pilot and a 152 main iirc. It does feel very rich but I will do several plug chops to keep an eye on it. Running up to Scarborough for a few days on Monda...
- Wed Jun 06, 2012 12:03 am
- Forum: Lambretta Tech
- Topic: Ron Moss - Avanti TT3 - Cylinder Kit - Review & Test.....
- Replies: 750
- Views: 299013
Re: Ron Moss - Avanti TT3 - Cylinder Kit - Review & Test....
Has anyone mated up an avanti kit with a 30mm pwk type carb and a jl3 pipe? I am going to need the base jetting sizes when I fit the kit at the weekend. Can anyone help please? Cheers Ron e-mailed the following to me when I asked him for a ballpark for the above "The customer running one of th...
- Tue Jun 05, 2012 9:17 pm
- Forum: Lambretta Tech
- Topic: Ron Moss - Avanti TT3 - Cylinder Kit - Review & Test.....
- Replies: 750
- Views: 299013
Re: Ron Moss - Avanti TT3 - Cylinder Kit - Review & Test....
Has anyone mated up an avanti kit with a 30mm pwk type carb and a jl3 pipe? I am going to need the base jetting sizes when I fit the kit at the weekend.
Can anyone help please?
Cheers
Can anyone help please?
Cheers
- Wed May 30, 2012 11:54 pm
- Forum: Lambretta Tech
- Topic: Carb and jetting help needed please
- Replies: 7
- Views: 1702
Re: Carb and jetting help needed please
Will check the float height, cheers.
It's the needles that I am having trouble finding, will see what time I finish and pop down sat if I can Jason, cheers mate
It's the needles that I am having trouble finding, will see what time I finish and pop down sat if I can Jason, cheers mate
- Wed May 30, 2012 10:09 pm
- Forum: Lambretta Tech
- Topic: Carb and jetting help needed please
- Replies: 7
- Views: 1702
Re: Carb and jetting help needed please
Sounds like I need a new carb then, which is best? Jason, it has the clear plastic bowl on it, it's very hard to see if it's full when flat in top gear. Apparently there is some mod about drilling out the needle valve on these? Any one know what it involves? Have you got and good carbs in Jason? Che...
- Wed May 30, 2012 7:47 pm
- Forum: Lambretta Tech
- Topic: Carb and jetting help needed please
- Replies: 7
- Views: 1702
Carb and jetting help needed please
Hello, Trying to jet an oko pwk carb on a ported iron cylinder sil 200. It has a sterling pipe on it. The carb size is 30mm. The problem I have is that no matter what main jet I put in it, when I am in top gear on full throttle after about 5secs, the engine goes boggy and splutters, then dies. If I ...