My main jet is 105 ( big difference from above)
Sent from my GT-I8190N using Tapatalk
Search found 164 matches
- Wed Mar 26, 2014 5:13 pm
- Forum: Vespa Tech
- Topic: fuel consumption malossi 220
- Replies: 17
- Views: 5926
- Wed Mar 26, 2014 5:12 pm
- Forum: Vespa Tech
- Topic: fuel consumption malossi 220
- Replies: 17
- Views: 5926
Re: fuel consumption malossi 220
I get about 55 miles per tank similar set up which has been dialed in on dyno.
Sent from my GT-I8190N using Tapatalk
Sent from my GT-I8190N using Tapatalk
- Fri Feb 21, 2014 7:40 pm
- Forum: Vespa Tech
- Topic: parmakit ....so underated
- Replies: 16
- Views: 7301
Re: parmakit ....so underated
Spec is 60 stroke worb5 crank,bgm reed valve with 350lc reeds, right hand jl pipe and 28mil dellorto run through the air box.... Oh and tuned by my mate Darrel Taylor My parmakit with similar set is nearly 20 bhp on the dyno with similar set up. GPS top speed 78mph cruises GPS 67 mph. Then saw Darr...
- Sat Jan 11, 2014 4:44 pm
- Forum: Vespa Tech
- Topic: malossi 210 and phbh 28 set up
- Replies: 33
- Views: 16497
Re: malossi 210 and phbh 28 set up
Sip digital speedo showed 67 which needs adjustment . Garmin gps showed true speed.
Prior to rebuild it was dynod at diablo moto at 18 bhp with a jl rh pipe .
Ran far better with sip pipe smoother through the gears.
Third gear is good pulls well
Sent from my GT-I8190N using Tapatalk
Prior to rebuild it was dynod at diablo moto at 18 bhp with a jl rh pipe .
Ran far better with sip pipe smoother through the gears.
Third gear is good pulls well
Sent from my GT-I8190N using Tapatalk
- Sat Jan 11, 2014 4:08 pm
- Forum: Vespa Tech
- Topic: malossi 210 and phbh 28 set up
- Replies: 33
- Views: 16497
Re: malossi 210 and phbh 28 set up
Just got my sausage speed tuned malossi 210 back after its had new rings and MB BGM box pipe fitted its running a phbh 28 ml delorto with the following set up main jet 130 pilot jet 50 atomiser AV266 needle x7 (on top notch) 45 slide air screw 1/2 out just come back after 30 mile run as I want to ma...
- Wed Jan 01, 2014 3:17 pm
- Forum: Vespa Tech
- Topic: Polossi 220?
- Replies: 36
- Views: 12959
Re: Polossi 220?
That's really helpful as I destroyed diablos finest it complete new internals so the 221 is now looking favourite are you going 28 or 30 ml carb on the Reed valve
Sent from my GT-I8190N using Tapatalk
Sent from my GT-I8190N using Tapatalk
- Wed Jan 01, 2014 3:10 pm
- Forum: Vespa Tech
- Topic: Polossi 220?
- Replies: 36
- Views: 12959
Re: Polossi 220?
So going back to joeys initial post what benifit in putting a malossi piston in a polini . I think sip sell a worb 5 like this but steel barrel
Sent from my GT-I8190N using Tapatalk
Sent from my GT-I8190N using Tapatalk
- Wed Jan 01, 2014 2:00 pm
- Forum: Vespa Tech
- Topic: Polossi 220?
- Replies: 36
- Views: 12959
Re: Polossi 220?
Is the 221 an aly barrel ? Available from sip ??
Sent from my GT-I8190N using Tapatalk
Sent from my GT-I8190N using Tapatalk
- Wed Jan 01, 2014 1:25 pm
- Forum: Vespa Tech
- Topic: Polossi 220?
- Replies: 36
- Views: 12959
Re: Polossi 220?
Stupid question time !fastfrog wrote:Very similar mould for both cylinder. Pistons look alsa very similar. Just put the new ally top end and run!!
so a 60 ml longstroke crank will fit with the aly 210 kit out the box and without any other mechanical alterations or need for other pistons etc??
- Wed Jan 01, 2014 12:16 pm
- Forum: Vespa Tech
- Topic: Polossi 220?
- Replies: 36
- Views: 12959
Re: Polossi 220?
As the other thread shows I killed my diablo moto polini :cry: :cry: :cry: :cry: Im now going to go for the aly kit as opposed to the steel 208 that was fitted as I had a couple of high speed heat seizes on the M way So questions!! Will the new ally 210 kit work with a 60 ml longstroke crank that wa...