Search found 40 matches

Go to advanced search

by andy summers
Fri Jun 28, 2013 1:43 pm
Forum: Lambretta Tech
Topic: PM Tuning Volante antidive disc brake
Replies: 19
Views: 11289

Re: PM Tuning Volante antidive disc brake

would you lower it or weld it higher up the fork leg ? how does this influence the dive/ride ?
by andy summers
Thu Jun 27, 2013 12:56 pm
Forum: Lambretta Tech
Topic: PM Tuning Volante antidive disc brake
Replies: 19
Views: 11289

PM Tuning Volante antidive disc brake

hi, Just fitting a PM tuning anit dive brake, can someone upload a pic of where the tab on the antidive link needs welding to the forks please? Ive read the instructions which I understand and also spoke to PM tuning, but my OCD is taking over!!! id like to double double check before welding so anyo...
by andy summers
Thu Jan 17, 2013 2:57 pm
Forum: Lambretta Tech
Topic: Kick Start Jamming??
Replies: 6
Views: 3929

Re: Kick Start Jamming??

Thanks for the replies. The piston doesnt seem to be sticking. it fully returns to its starting point and the teeth that mesh with the gear cog are not sticking out too far. Ive checked the chain tension and all is OK and isnt catching/snagging the chain guide. Ive not tried holding in the clutch le...
by andy summers
Wed Jan 16, 2013 6:22 pm
Forum: Lambretta Tech
Topic: Kick Start Jamming??
Replies: 6
Views: 3929

Kick Start Jamming??

Hi, When my li s2 has been stood for a while (im talking overnight/days) the kickstart jams when trying to kick over. its strange as sometimes it will kick over, then jam, then kick over again. Eventually after about 20 attempts it starts to free up so i can get a good kick so it will fire. If I the...
by andy summers
Fri Apr 13, 2012 11:47 am
Forum: Lambretta Tech
Topic: Italian series 2 legshields
Replies: 2
Views: 1541

Re: Italian series 2 legshields

Hi Having problems working out how I fit the mudguard lower fixings onto series 2 legshields. They have the 2 locating lugs/mounting points but are they supposed to be threaded? If so mine seem to be stripped or do I some how need to slip a nut inside the lug to thread he bolt through?? :? Thanks i...
by andy summers
Thu Apr 12, 2012 11:23 pm
Forum: Lambretta Tech
Topic: Italian series 2 legshields
Replies: 2
Views: 1541

Italian series 2 legshields

Hi Having problems working out how I fit the mudguard lower fixings onto series 2 legshields. They have the 2 locating lugs/mounting points but are they supposed to be threaded? If so mine seem to be stripped or do I some how need to slip a nut inside the lug to thread he bolt through?? :? Thanks in...
by andy summers
Mon Dec 05, 2011 2:50 pm
Forum: Lambretta Tech
Topic: Unable to start series 2
Replies: 47
Views: 16391

Re: Unable to start series 2

Ive swapped the 20m carb to the original series 2 manifold and carb and loads more room, series 2 carb sitting up nice and stright! I bought (what i was told) a manifold from an original TV175 s3 for the sh1/20 delly but it sits far too close to the engine mount as shown. can anyone send me a link f...
by andy summers
Fri Dec 02, 2011 12:26 pm
Forum: Lambretta Tech
Topic: Unable to start series 2
Replies: 47
Views: 16391

Re: Unable to start series 2

Just looked at your picture and that angle is WAY out. I'm not sure if it is the cause of your problem but it certainly won't help and you need to do something about it. I should think it could cause either fuel starvation or more likely flooding in your case. I would try the S2 carb on it and not ...
by andy summers
Fri Dec 02, 2011 10:23 am
Forum: Lambretta Tech
Topic: Unable to start series 2
Replies: 47
Views: 16391

Re: Unable to start series 2

Seems that the engine is receiving too much fuel on the start and requires more air. Will it run okay without the air bellow for a while or will it still die after a little bit? When you pull the choke, will it die inmediately? Also, have you tried another carburettor, just for the sake of it? Best...
by andy summers
Fri Dec 02, 2011 12:06 am
Forum: Lambretta Tech
Topic: Unable to start series 2
Replies: 47
Views: 16391

Re: Unable to start series 2

Also would the angle of the carb affect it's operation? I can't make it sit up right anymore due to the engine mount being in the way. When I changed the jets earlier the bowl was nearly full.

http://m1134.photobucket.com/albumview/ ... g.html?o=0

Go to advanced search

Powered by phpBB™ • Design by PlanetStyles