Search found 17 matches
- Thu Mar 25, 2010 8:20 pm
- Forum: Lambretta Tech
- Topic: Engine strip questions
- Replies: 15
- Views: 4647
Re: Engine strip questions
Do this many times in my job it works on broken studs damaged screws any think with a thread .And have actually done this job not so long a go .firstly clean the head of screw .place a m8 or m10 nut over the screw head and hold with a pair of long nose pliers .using a mig welder set to a good penatr...
- Mon Mar 22, 2010 10:42 pm
- Forum: Lambretta Tech
- Topic: LTH CHAIN TENSIONER
- Replies: 2
- Views: 1701
Re: LTH CHAIN TENSIONER
another thought is to mill 1mm of the back of the support plt. as its 4mm thick .that would give about 5mm clearance if i lose the bottom guide as well
- Sun Mar 21, 2010 8:08 pm
- Forum: Lambretta Tech
- Topic: LTH CHAIN TENSIONER
- Replies: 2
- Views: 1701
LTH CHAIN TENSIONER
Is anyone using this tensioner that pulls the chain down . .Fitted one today with a bottom chain guide .And a little concerned that the chain runs close to the supporting plt on the tensioner that bolts to the crankcase.I measured from the face of a pin on the chain to the face of the support plt an...
- Fri Feb 26, 2010 12:26 pm
- Forum: Lambretta Tech
- Topic: End plate
- Replies: 0
- Views: 1128
End plate
Hi all .Would any one have pictures on the end plt conversion from gp to early type .The absoloutley guide pictures have been deleted.thanks
- Mon Jan 18, 2010 1:56 pm
- Forum: Lambretta Tech
- Topic: frank sanderson anti-dive set up.
- Replies: 4
- Views: 2017
Re: frank sanderson anti-dive set up.
Alright jhonny youll be fine using your scootsrs one . have to catch up some time 
Darren
Darren- Sat Dec 05, 2009 11:08 pm
- Forum: Lambretta Tech
- Topic: Lambretta Inovations Hub Question
- Replies: 5
- Views: 2213
Re: Lambretta Inovations Hub Question
one of the washers that sits next to the bearing .if it can touch the outer edge of the bearing .it will make the wheel bind 
- Wed Nov 04, 2009 11:36 pm
- Forum: Lambretta Tech
- Topic: gear box chatter
- Replies: 12
- Views: 4473
Re: gear box chatter
Hi Darren I had what sounds like the same problem with my GP when I changed the 150 GP box for an Li 150 one and after lots of changed parts and adjustments shims etc it was fixed the way knowledge said. hi lazarus found filings on magnetic drain plug too much for 10 miles . so this evening strippe...
- Tue Nov 03, 2009 8:42 pm
- Forum: Lambretta Tech
- Topic: gear box chatter
- Replies: 12
- Views: 4473
Re: gear box chatter
good tips knowledge like it . but the kick start is not engaging on first gear . with engine running put hand on kickstart push down 1/2 inch and then the plunger engages 1st gear .gp end plt . had no problems until i changed gear boxes.
- Tue Nov 03, 2009 8:02 pm
- Forum: Lambretta Tech
- Topic: gear box chatter
- Replies: 12
- Views: 4473
Re: gear box chatter
pretty shore now i found the problem .went for a ride on the main road 30-40 mph .do a leisurely change down from 4th to 3rd and the gears wont mesh.do a quick one and they mesh .give it the gun in first and there is defintley a ting ting coming from the gear box .so stripping down when i can . chan...
- Mon Nov 02, 2009 9:17 pm
- Forum: Lambretta Tech
- Topic: gear box chatter
- Replies: 12
- Views: 4473
Re: gear box chatter
[quote="Matty"]Have you checked how the gearbox sits with the layshaft? I fitted an Italian SX200 gearbox to my Indian case and luckily it was just about spot on with a 2.0mm shim: all checked mate gears sit above lay shaft .hard facing on gears and cluster looked perfect .and measured gea...