sleeving
Posted: Sat Oct 24, 2009 9:03 pm
ok who does the steel liners prefer them not to pull thi pants down on the price if possible?
Scooterotica
The UK's No1 Lambretta & Vespa Scooter Forum.
https://www.scooterotica.org/forum/
sleeving
Page 1 of 3
Re: sleeving
Posted: Sat Oct 24, 2009 11:52 pm
quality cost and you wont beat these guys for service ,quality and detail not had a cylinder relighned but had rebores and a car block honed by them they put alot of scooter dealers to shame with there knowledge proper british enginners http://www.pjme.co.uk/
Re: sleeving
Posted: Sun Oct 25, 2009 4:56 pm
I use PJme for my crank rebuilds and there work is top quality I have also used them for a couple of re sleevs and the finish was second to none I am not so sure if they do any pistons or sleves for lamys you will have to give them a call on 01902 307457shocky wrote:quality cost and you wont beat these guys for service ,quality and detail not had a cylinder relighned but had rebores and a car block honed by them they put alot of scooter dealers to shame with there knowledge proper british enginners http://www.pjme.co.uk/
Cheers
Mick
Re: sleeving
Posted: Sun Oct 25, 2009 5:02 pm
they have done several TS1 kits and some out to 71mm using the weisco piston
Re: sleeving
Posted: Sun Oct 25, 2009 11:23 pm
Try Fahron engineering in Hucknall, Notts. They've done a couple for me, good price and good quality. I'll dig out their number tomorow at work.
Re: sleeving
Posted: Sun Oct 25, 2009 11:31 pm
I contacted pjme recently, to reline a rapido will cost £120 but you have to supply a piston of choice.
I would like to see the details of the hucknall chaps, only down the road from me .
I would like to see the details of the hucknall chaps, only down the road from me .
Re: sleeving
Posted: Mon Oct 26, 2009 1:05 am
ooooo just been given a ts1 200 barrel decisions decisions whats thi to do????????????????????
Re: sleeving
Posted: Mon Oct 26, 2009 8:05 am
Fahron Engineering
Wighay Road
Hucknall
Notts NG15 8AH
Tel. 01159 634 123.
No website I'm afraid, he doesn't advertise.
I know he used to do a lot of barrels and cranks for SES, he knows 2 strokes aswell.
Wighay Road
Hucknall
Notts NG15 8AH
Tel. 01159 634 123.
No website I'm afraid, he doesn't advertise.
I know he used to do a lot of barrels and cranks for SES, he knows 2 strokes aswell.
Re: sleeving
Posted: Mon Oct 26, 2009 1:11 pm
cheers pal had a chat wi him today and i will be using his services just need to find a good piston kitsideswipe wrote:Fahron Engineering
Wighay Road
Hucknall
Notts NG15 8AH
Tel. 01159 634 123.
No website I'm afraid, he doesn't advertise.
I know he used to do a lot of barrels and cranks for SES, he knows 2 strokes aswell.
Re: sleeving
Posted: Mon Oct 26, 2009 2:02 pm
so how much does he charge for this compaired to pjmeC*NTSPEED wrote:cheers pal had a chat wi him today and i will be using his services just need to find a good piston kitsideswipe wrote:Fahron Engineering
Wighay Road
Hucknall
Notts NG15 8AH
Tel. 01159 634 123.
No website I'm afraid, he doesn't advertise.
I know he used to do a lot of barrels and cranks for SES, he knows 2 strokes aswell.