TSR Evo Tail can support

Anything related to Lambrettas... ask tech questions, post helpful info, or just read and learn.
Norrie Bodge
registered user
Posts: 464
Joined: Thu Oct 25, 2012 2:49 am
Main scooter: GP-1971-Ts230/S2-1960-Ts230
Contact:

Sat Nov 09, 2019 1:26 pm

essexgp wrote:
Fri Nov 08, 2019 5:32 pm
Norrie Bodge wrote:
Fri Nov 08, 2019 2:07 am
essexgp wrote:
Thu Nov 07, 2019 7:45 pm


Which SIP endcan do you use? as my Evo support bracket is fouling my GP side panel to
I haven’t used my TSR pipe yet m8 so not changed end can
But was informed it’s these ->. https://www.sip-scootershop.com/en/prod ... ng_20006ca
Thanks for that info but do you mean the SIP or the PM one? sorry to be thick

This one which in the description says same stud spacing as a PM

https://www.sip-scootershop.com/en/prod ... ng_20006ca

Scooterdude
registered user
Posts: 796
Joined: Sat May 28, 2016 4:51 pm
Main scooter: Lambretta LI 125 S3
Location: Skaville
Contact:

Sat Nov 09, 2019 3:15 pm

I can confirm the cans sold by Chiselspeed as fitted to their exhaust range share the same stud spacing as the TSR evo.

holty
registered user
Posts: 880
Joined: Wed Jul 15, 2015 11:52 pm
ebay user ID: amholt123
Main scooter: lambretta gp
Location: east yorkshire
Contact:

Sat Nov 09, 2019 7:28 pm

you other option would be to alter the bracket, ive apapted one on my gp and its more or less under the end can, I do have a non standard exhaust so I had to make my own mounting on the engine, then a rubber bobbin, then cut and welded the bracket to fit between the two.

Norrie Bodge
registered user
Posts: 464
Joined: Thu Oct 25, 2012 2:49 am
Main scooter: GP-1971-Ts230/S2-1960-Ts230
Contact:

Sun Nov 10, 2019 1:11 am

holty wrote:
Sat Nov 09, 2019 7:28 pm
you other option would be to alter the bracket, ive apapted one on my gp and its more or less under the end can, I do have a non standard exhaust so I had to make my own mounting on the engine, then a rubber bobbin, then cut and welded the bracket to fit between the two.

Any piccys mate?

Hughieboy
registered user
Posts: 79
Joined: Mon May 25, 2015 8:37 am
Main scooter: Lambretta Li S2 GT186
Location: The Shire
Contact:

Sun Nov 10, 2019 6:08 pm

holty wrote:
Sat Nov 09, 2019 7:28 pm
you other option would be to alter the bracket, ive apapted one on my gp and its more or less under the end can, I do have a non standard exhaust so I had to make my own mounting on the engine, then a rubber bobbin, then cut and welded the bracket to fit between the two.
Thanks everyone.... photos of your bracket would be great!

User avatar
essexgp
registered user
Posts: 312
Joined: Wed Jan 07, 2009 6:16 pm
Main scooter: Indian Gp200 Indian Gp Cutdown
Location: Canvey Island
Contact:

Sun Nov 10, 2019 6:15 pm

Scooterdude wrote:
Sat Nov 09, 2019 3:15 pm
I can confirm the cans sold by Chiselspeed as fitted to their exhaust range share the same stud spacing as the TSR evo.
Thanks for the info

User avatar
essexgp
registered user
Posts: 312
Joined: Wed Jan 07, 2009 6:16 pm
Main scooter: Indian Gp200 Indian Gp Cutdown
Location: Canvey Island
Contact:

Sun Nov 10, 2019 6:16 pm

Norrie Bodge wrote:
Sat Nov 09, 2019 1:26 pm
essexgp wrote:
Fri Nov 08, 2019 5:32 pm
Norrie Bodge wrote:
Fri Nov 08, 2019 2:07 am


I haven’t used my TSR pipe yet m8 so not changed end can
But was informed it’s these ->. https://www.sip-scootershop.com/en/prod ... ng_20006ca
Thanks for that info but do you mean the SIP or the PM one? sorry to be thick

This one which in the description says same stud spacing as a PM

https://www.sip-scootershop.com/en/prod ... ng_20006ca
Thanks again for the info

User avatar
GTFOMWSC
registered user
Posts: 324
Joined: Sat Jan 01, 2011 5:49 pm
ebay user ID: itsthewillo
Main scooter: GP230 Super Monza CS Tuned
Location: Rugby
Contact:

Mon Nov 11, 2019 8:19 am

The trouble is we shouldn't have to do all this they cost enough money why should we end up fixing there crap.On mine also the 2 holes for the barrell studs were not far enough apart so i had to take my old JL manifold and clamp it together with the evo one and drill them through so it would fit,i'm told this has been common on a few of them as well.TBH it's bull we don't buy them to do all this they should fit right and to make a half attempt at a rear bracket that looks and fits sh*te just shows poor quality control(unfortunately same as the SIP road 2 vespa exhausts).
the man don't give a f@@k

Hughieboy
registered user
Posts: 79
Joined: Mon May 25, 2015 8:37 am
Main scooter: Lambretta Li S2 GT186
Location: The Shire
Contact:

Mon Nov 11, 2019 11:44 pm

GTFOMWSC wrote:
Mon Nov 11, 2019 8:19 am
The trouble is we shouldn't have to do all this they cost enough money why should we end up fixing there crap.On mine also the 2 holes for the barrell studs were not far enough apart so i had to take my old JL manifold and clamp it together with the evo one and drill them through so it would fit,i'm told this has been common on a few of them as well.TBH it's bull we don't buy them to do all this they should fit right and to make a half attempt at a rear bracket that looks and fits sh*te just shows poor quality control(unfortunately same as the SIP road 2 vespa exhausts).
Amen to that!

Post Reply Previous topicNext topic
  • Information
  • Who is online

    Users browsing this forum: Majestic-12 [Bot] and 1 guest