Re: Toolbox Flywheel Holder
Posted: Thu Sep 30, 2010 3:13 pm
Nice one, looking forward to trying and freeing some space in my toolbox 
Scooterotica
The UK's No1 Lambretta & Vespa Scooter Forum.
https://www.scooterotica.org/forum/
Toolbox Flywheel Holder
Page 6 of 10
Re: Toolbox Flywheel Holder
Posted: Thu Sep 30, 2010 4:19 pm
Yep, looks good, well done
Re: Toolbox Flywheel Holder
Posted: Thu Sep 30, 2010 4:43 pm
Top piece of work, well done.
Re: Toolbox Flywheel Holder
Posted: Thu Sep 30, 2010 5:52 pm
Nice...can i have one aswell mate.
Re: Toolbox Flywheel Holder
Posted: Fri Oct 01, 2010 12:16 pm
I'VE P.M.'D YA.......dapper wrote:Right, at long last I'm getting a batch of ten made to start with. I should be picking them up on Thursday and will try one against my own scoot first. I'll post a photo of the finished article. They will be £10.00 + P&P. If there is sufficient demand I'll get another larger batch made which may be a bit cheaper, so the tight b@5t@rds out there can wait for the guinea pigs to try them first at the more expensive rate
Re: Toolbox Flywheel Holder
Posted: Sat Oct 02, 2010 12:12 pm
methleymongo wrote:I'VE P.M.'D YA.......dapper wrote:Right, at long last I'm getting a batch of ten made to start with. I should be picking them up on Thursday and will try one against my own scoot first. I'll post a photo of the finished article. They will be £10.00 + P&P. If there is sufficient demand I'll get another larger batch made which may be a bit cheaper, so the tight b@5t@rds out there can wait for the guinea pigs to try them first at the more expensive rate
I DEFINATELY WANT ONE THOUGH!!!!!
Re: Toolbox Flywheel Holder
Posted: Fri Oct 08, 2010 5:27 pm
Right, as I'm at work tomorrow, I'll pop over to the PO to get one weighed in a Jiffy bag so I can advise P&P costs. I have nine ready to go out (Soulsurfer wants two, greedy beggar ). I'll PM those that have said they want one with my postal addy for cheques. Once cheque is received and cleared, tool will be posted. Anyone whose cheque bounces will be villified on here
). I'll PM those that have said they want one with my postal addy for cheques. Once cheque is received and cleared, tool will be posted. Anyone whose cheque bounces will be villified on here Re: Toolbox Flywheel Holder
Posted: Thu Oct 14, 2010 2:44 pm
Right, P&P will be £1.32 for one tool or £1.59 for two posted out second class with proof of posting, all in a nice new Jiffy bag. All those interested will receive a PM with my postal addy.
Re: Toolbox Flywheel Holder
Posted: Thu Oct 14, 2010 3:05 pm
dapper wrote:Right, P&P will be £1.32 for one tool or £1.59 for two posted out second class with proof of posting, all in a nice new Jiffy bag. All those interested will receive a PM with my postal addy.
Thanks
Re: Toolbox Flywheel Holder
Posted: Thu Oct 14, 2010 4:03 pm
Right, all those that have shown an interest have now been sent PMs. Please don't forget to include your postal addy.
I'll welcome any comments about the tool and its ease of use, or possible improvements but remember, I am a soft southerner and don't have a thick skin so be gentle. I tried it against a long finned flywheel at Wicksteed, and it would appear to require 35mm. bolts instead of the 30mm. I mentioned earlier in the thread. Also, please remember, I did say I wasn't sending out the bolts as well 
I'll welcome any comments about the tool and its ease of use, or possible improvements but remember, I am a soft southerner and don't have a thick skin so be gentle.
I tried it against a long finned flywheel at Wicksteed, and it would appear to require 35mm. bolts instead of the 30mm. I mentioned earlier in the thread. Also, please remember, I did say I wasn't sending out the bolts as well