Page 2 of 3
Re: Im building a Yamaha engined YPVS 350 Lambretta
Posted: Sat Mar 26, 2011 2:50 pm
by Ripfx
soulsurfer wrote:Hi Karl, hope you're well,
Knowing what you're capable of, I'm sure this'll be as superb as your other projects, keep us posted mate
Hi Mike,
Im fine mate hope you are too,
Thanks for the words of encouragement
PS
I love the trainers
Re: Im building a Yamaha engined YPVS 350 Lambretta
Posted: Sat Mar 26, 2011 2:55 pm
by Ripfx
Wayne Miller wrote:RICSPEED wrote:i suppose the Rossa's sat higher at the back because of the petrol tank above the rear wheel ........incidentally .....where is the tank???
Ive got visions of ripfx reading your post and suddenly saying 'Oh f@@k!'
hope this isnt the case, funny as f@@k if it is though.
Best of luck finishing the build
'Oh f@@k!'
Re: Im building a Yamaha engined YPVS 350 Lambretta
Posted: Sat Mar 26, 2011 2:58 pm
by soulsurfer
Did you get this as a part fininished project or have you done it yourself, or is it Frank's doing?
Re: Im building a Yamaha engined YPVS 350 Lambretta
Posted: Sat Mar 26, 2011 3:03 pm
by Ripfx
scooty wrote:RICSPEED wrote:
just wondering what the purple ally thing is now
cant see a seperate rev counter so might be a shift light? rev counter could be in speedo tho
nice to see the use of centre single shocker
The purple ally thing is a digital water temp gauge.
The tacho, tank gauge and idiot lights are combined in the round digital speedo in the headset..
Re: Im building a Yamaha engined YPVS 350 Lambretta
Posted: Sat Mar 26, 2011 3:06 pm
by Ripfx
soulsurfer wrote:Did you get this as a part fininished project or have you done it yourself, or is it Frank's doing?
All my own work but I did buy the white fibreglass panels from Frank
Re: Im building a Yamaha engined YPVS 350 Lambretta
Posted: Sat Mar 26, 2011 3:17 pm
by Ripfx
RICSPEED wrote:nice ,
but im a little concered with the way it sits on the stand
Its a good quality stand and seems to be up to the job,
But as this is just a dry build I might also fit a side stand before I rip the scooter apart for spraying...
Re: Im building a Yamaha engined YPVS 350 Lambretta
Posted: Sat Mar 26, 2011 3:20 pm
by soulsurfer
Ripfx wrote:soulsurfer wrote:Did you get this as a part fininished project or have you done it yourself, or is it Frank's doing?
All my own work but I did buy the white fibreglass panels from Frank
I'll look forward to this one then
Re: Im building a Yamaha engined YPVS 350 Lambretta
Posted: Sat Mar 26, 2011 4:34 pm
by RICSPEED
Ripfx wrote:RICSPEED wrote:nice ,
but im a little concered with the way it sits on the stand
Its a good quality stand and seems to be up to the job,
But as this is just a dry build I might also fit a side stand before I rip the scooter apart for spraying...
i was wondering if the rear wheel was too far up ....a pic off the stand i think
Re: Im building a Yamaha engined YPVS 350 Lambretta
Posted: Sat Mar 26, 2011 9:41 pm
by MADSPEEDRB260
Looks good mate well done..
Re: Im building a Yamaha engined YPVS 350 Lambretta
Posted: Thu Mar 31, 2011 10:10 pm
by resin_nick
well nice fella like it . you not karl hissey are u ?