Ts1 Rebuild questions

Anything related to Lambrettas... ask tech questions, post helpful info, or just read and learn.
User avatar
jimmo
registered user
Posts: 67
Joined: Sun Apr 12, 2009 10:35 pm
Main scooter: Lambretta GP TS1 230 JB
Location: Chertsey - Surrey
Contact:

I attempted a spin out today but ended earlier than expected!
Heard a knocking noise from the top end and the it wouldnt settle down when the throttle is released.

Got home and took the engine apart and found the following.

The top ring retaining peg on the piston as gone and the ring ends dont look to clever.
The barrel it self seems ok with no scores visable.
When I removed the crank on both outward sides of the webs there is a build up of what looks like black grease!.

Does this indicate that the oilseals are gone causing an air leaking making the mixture lean?

Obviously I'm going to replace both bearings, 3 x oil seals and a new piston/rings.
Question is which bearings/seals should I be using and second which piston should i get - An Asso or Wisco or one of Broadys Pistons?

Also should I be looking at changing anything else whilst the engine is apart?

Thanks

;) ;)
DJB
Dealer
Posts: 186
Joined: Sun Nov 15, 2009 6:35 pm
Location: Colchester
Contact:

Check the big end aswell. I would try a wossner piston, as they are alot cheaper than most.
User avatar
jimmo
registered user
Posts: 67
Joined: Sun Apr 12, 2009 10:35 pm
Main scooter: Lambretta GP TS1 230 JB
Location: Chertsey - Surrey
Contact:

Another question!

Checking on Broadys website and there are 4 grades of piston - a,b,c,d.

How can i tell what grade I need?- is there some marking on the barrel that indicates what the grade of the barrel is?

Thanks again
;)
YAMLAM
registered user
Posts: 1073
Joined: Mon Jan 12, 2009 10:41 pm
Contact:

Hi james,glad you made it back home . yes there should be a corrisponding a b c or d stamped on the barrel.
win or lose have a booze
User avatar
jimmo
registered user
Posts: 67
Joined: Sun Apr 12, 2009 10:35 pm
Main scooter: Lambretta GP TS1 230 JB
Location: Chertsey - Surrey
Contact:

Got back ok - what do you reckon of that black sludge on the crank webs?
Shagged oil seals?

Gonna sort the bits out tommorrow so should be on the road by the weekend

Many there today?
User avatar
wack 63
registered user
Posts: 1254
Joined: Fri Nov 27, 2009 9:33 pm
Main scooter: '71 GP TS1
Location: Lincs
Contact:

I would recommend contacting Harry Barlow(Pro Porting) he was doing a bearing/viton seal set today at Kettering for £45 and were top quality. Not seen the Wossner pistons but can assure you the MRB ones are top notch and are unlikely to have the same probs as with the Asso brick.The black grease is probably a sign the seals have gone or someone was over enthusastic with the grease when fitting the crank. The cylinder size grade is stamped on the little flat joined to the head gasket face.
User avatar
jimmo
registered user
Posts: 67
Joined: Sun Apr 12, 2009 10:35 pm
Main scooter: Lambretta GP TS1 230 JB
Location: Chertsey - Surrey
Contact:

wack 63 wrote:I would recommend contacting Harry Barlow(Pro Porting) he was doing a bearing/viton seal set today at Kettering for £45 and were top quality. Not seen the Wossner pistons but can assure you the MRB ones are top notch and are unlikely to have the same probs as with the Asso brick.The black grease is probably a sign the seals have gone or someone was over enthusastic with the grease when fitting the crank. The cylinder size grade is stamped on the little flat joined to the head gasket face.

Ta mate, i've Harry's number somewhere,I'll give him a bell.

So MBD 's pistons are a quality bit of kit then ?

Thanks again

;)
User avatar
GP Kevo
registered user
Posts: 321
Joined: Wed Mar 11, 2009 7:48 am
Main scooter: 1969 150 DL / GP225 TS1
Location: Warsaw
Contact:

Yes, MB RaceTour pistons probably the best you can fit to a Lambretta. Just remember to check ring end gap at 1,000 miles, as MB says, as many pistons seem to be getting excessive ring end wear during running in.
DJB
Dealer
Posts: 186
Joined: Sun Nov 15, 2009 6:35 pm
Location: Colchester
Contact:

Last edited by DJB on Sun Mar 07, 2010 8:45 pm, edited 1 time in total.
User avatar
soulsurfer
registered user
Posts: 2539
Joined: Thu Jan 08, 2009 2:43 pm
Location: The Garden Of England
Contact:

Is the Wossner a cast or forged piston Dave?
I'm going the Monza piston with a head machined to suit myself.
Turn On, Tune In, Cop out!
Post Reply Previous topicNext topic
  • Information
  • Who is online

    Users browsing this forum: Google [Bot] and 21 guests