S2 Eibar wiring diagram.

Anything related to Lambrettas... ask tech questions, post helpful info, or just read and learn.
wrecklessrobbie
registered user
Posts: 394
Joined: Thu Jan 09, 2014 7:34 pm
Main scooter: li150
Location: York
Contact:

Can anybody point me in the right direction to find a wiring diagram for an Eibar s2.
I am using the original light switch and cut out switch and connector blocks in the headset.
I have fitted a new AF wiring loom and 12v electronic stator, regulator and cdi.
The light switch colours seem to be different to Italien and am wondering where the new AF loom cables go.

Robbie
User avatar
HxPaul
registered user
Posts: 1110
Joined: Fri Dec 06, 2013 1:58 pm
Main scooter: lambretta Li 150
Location: Halifax,Yorkshire
Contact:

Try Antony at Buzzsolomoto.
wrecklessrobbie
registered user
Posts: 394
Joined: Thu Jan 09, 2014 7:34 pm
Main scooter: li150
Location: York
Contact:

Ok
Its the af wiring loom thats confusing me.
That has grey, brown,black and green.
Im thinking green should go to connector block and cut out switch.
Not sure on the others
mick1
registered user
Posts: 1292
Joined: Sun Dec 04, 2011 7:43 pm
Main scooter: Li Avanti 225
Location: York
Contact:

not 100% but the black is usually the back light, the brown is the lighting feed, agree about the green and the grey ......hmmm not sure ?
wrecklessrobbie
registered user
Posts: 394
Joined: Thu Jan 09, 2014 7:34 pm
Main scooter: li150
Location: York
Contact:

I shall look at the wires going to the back light and brake light.
I have wired them up. I suspect your right with the black. But need to check what i have done!!!
Trying to remember if grey was from the back brake.
Grey is back brake.
Black is back light.
Brown is running from regulator.
Green from cdi.
User avatar
HxPaul
registered user
Posts: 1110
Joined: Fri Dec 06, 2013 1:58 pm
Main scooter: lambretta Li 150
Location: Halifax,Yorkshire
Contact:

http://www.afrayspeed.co.uk/index.php?p ... ectricThis is an AF Rayspeed wiring diagram for a 12v system(this is for a series 3 with an ignition switch)and it shows clearly the grey wire in the loom and from what I can see it goes to the brake light switch.If you click on performance and scroll down,then click on electronic kit instructions.
wrecklessrobbie
registered user
Posts: 394
Joined: Thu Jan 09, 2014 7:34 pm
Main scooter: li150
Location: York
Contact:

Yeah i have looked at the af wiring diagram paul. 😊
Grey is brake
Brown feed from regulator
Green from cdi
Black from rear light.

So far i know green connects to kill switch on connection block
Not sure where grey brown and black go yet.
rosscla
registered user
Posts: 4823
Joined: Tue Oct 25, 2011 9:50 pm
Main scooter: Lambretta
Location: Lanarkshire
Contact:

What wires are coming from the switch?
"Our dilemma is that we hate change and love it at the same time; what we really want is for things to remain the same but get better."
wrecklessrobbie
registered user
Posts: 394
Joined: Thu Jan 09, 2014 7:34 pm
Main scooter: li150
Location: York
Contact:

Cut out switch is green.

Light switch..
Has
Long single white...horn i think.
Yellow...sidelight i think
Red...headlight dip or main
Blue...headlight dip or main
Green
Grey
Black
Brown

Junction box has
Grey 3 holes
Blue.2 holes
Black 3 holes
Brown 3 holes
Green 2 holes....for cut out switch and green from cdi??

Light bulb holder has 4 holes
I think for blue, earth yellow and red?
rosscla
registered user
Posts: 4823
Joined: Tue Oct 25, 2011 9:50 pm
Main scooter: Lambretta
Location: Lanarkshire
Contact:

Id start by connecting the colours at the headset end

Blue/red will be your dip /main
Yellow to your sidelight

Loom - switch
Brown - Brown
Black to black
Grey to grey

Black also to speedo bulb

Not so sure about the green from the switch though.
"Our dilemma is that we hate change and love it at the same time; what we really want is for things to remain the same but get better."
Post Reply Previous topicNext topic
  • Information
  • Who is online

    Users browsing this forum: Google [Bot] and 19 guests