Mb rear bearings

General scooter chat, any scooter related non technical info.
User avatar
garry inglis
registered user
Posts: 1273
Joined: Tue Jul 21, 2015 8:04 pm
ebay user ID: garry52uk
Main scooter: ts1 230 and rb200
Location: darlington
Contact:

Sun Jul 09, 2017 11:20 am

does it just push out then saves heating casing and less risk of damage i think i would install it with the bearing in place so you get a true fit but in the future it should just tap out

fluff34567
registered user
Posts: 388
Joined: Tue Dec 20, 2016 2:27 pm
Location: Switzerland
Contact:

Sun Jul 09, 2017 2:44 pm

I suppose if you install the housing with a bearing retaining compound you could tap it out from inside but I would be inclined to use a bearing puller from outside instead then no stress on the housing at all.

User avatar
kejj
registered user
Posts: 389
Joined: Wed Jan 07, 2009 10:23 pm
Contact:

Tue Jul 11, 2017 3:49 pm

fluff34567 wrote:I suppose if you install the housing with a bearing retaining compound you could tap it out from inside but I would be inclined to use a bearing puller from outside instead then no stress on the housing at all.
Inhopp that i CSN replace the bearing without the housing moving out from the case. He who lives through a bearing will have to report back.



Sent from my iPhone using Tapatalk
________________________
Lambretta LiS150 1965 - MBGM RT195 w/MBGM Clubman & Keihin PWK28
Lambretta TV175 1962 - GranTurismo 200 w/MBGM Clubman & Dellorto PHBH 28
http://tv175.wordpress.com/

fluff34567
registered user
Posts: 388
Joined: Tue Dec 20, 2016 2:27 pm
Location: Switzerland
Contact:

Tue Jul 11, 2017 4:16 pm

Using a bearing puller is the best way

User avatar
garry inglis
registered user
Posts: 1273
Joined: Tue Jul 21, 2015 8:04 pm
ebay user ID: garry52uk
Main scooter: ts1 230 and rb200
Location: darlington
Contact:

Tue Jul 11, 2017 6:14 pm

hi kejj can you help me understand your japanese lol

fluff34567
registered user
Posts: 388
Joined: Tue Dec 20, 2016 2:27 pm
Location: Switzerland
Contact:

Tue Jul 11, 2017 8:09 pm

Hope bearing can be replaced without removing the housing. If someone has one and replaces the bearing let me know.

joespeed
registered user
Posts: 740
Joined: Wed Jan 07, 2009 10:57 am
Location: drax,near selby,north yorkshire
Contact:

Tue Jul 11, 2017 8:56 pm

fluff34567 wrote:Picked up my order from jockeys this morning. Some closer pics of their drive bearing solution. I don't have circlip pliers with me to see the full bearing number though.

The washers are spacers and the felt thing goes on the outer face .. not sure why though.ImageImageImage
this looks like a stepped sleeve that houses a stock sized bearing, hope it can take the hammer that the special lambretta one does!

User avatar
garry inglis
registered user
Posts: 1273
Joined: Tue Jul 21, 2015 8:04 pm
ebay user ID: garry52uk
Main scooter: ts1 230 and rb200
Location: darlington
Contact:

Tue Jul 11, 2017 9:12 pm

garry inglis wrote:does it just push out then saves heating casing and less risk of damage i think i would install it with the bearing in place so you get a true fit but in the future it should just tap out
That's what I was saying in the other post fluff

fluff34567
registered user
Posts: 388
Joined: Tue Dec 20, 2016 2:27 pm
Location: Switzerland
Contact:

Tue Jul 11, 2017 9:33 pm

joespeed wrote:
fluff34567 wrote:Picked up my order from jockeys this morning. Some closer pics of their drive bearing solution. I don't have circlip pliers with me to see the full bearing number though.

The washers are spacers and the felt thing goes on the outer face .. not sure why though.ImageImageImage
this looks like a stepped sleeve that houses a stock sized bearing, hope it can take the hammer that the special lambretta one does!
Exactly what it is. It's a low powered engine end of day and having seen numerous "original"bearings, some failing after a few weeks I'm confident this will last as the others have been shite.

User avatar
kejj
registered user
Posts: 389
Joined: Wed Jan 07, 2009 10:23 pm
Contact:

Wed Jul 12, 2017 2:57 pm

Autocorrect ruined my post. Was saying that I hope the bearing is removable without taking its metal seat it resides in out.


Sent from my iPhone using Tapatalk
________________________
Lambretta LiS150 1965 - MBGM RT195 w/MBGM Clubman & Keihin PWK28
Lambretta TV175 1962 - GranTurismo 200 w/MBGM Clubman & Dellorto PHBH 28
http://tv175.wordpress.com/

Post Reply Previous topicNext topic
  • Information
  • Who is online

    Users browsing this forum: No registered users and 2 guests