TSR DJ Exhaust
-
- registered user
- Posts: 28
- Joined: Wed Dec 02, 2015 10:46 pm
- Main scooter: Indian GP RT 225
- Contact:
Hi looking for some user experience of the TSR DJ lambretta exhaust, bang for buck, performance, build quality etc. My motor is an RT195 I quite like the look of them but hey ! looks shouldn't be the only consideration right ?
I borrowed one couldnt fit footboards and the bottom of the panel needed trimming I could have modified it to fit but it wasnt mine not sure of its originDonnie wrote:Best ask about fitment issues too!
We sleep soundly in our beds because rough men stand ready in the night to visit violence on those who would do us harm
-
- registered user
- Posts: 156
- Joined: Fri Jan 09, 2009 11:14 am
- Main scooter: Lambretta GP Monza 225
- Location: Livingston
- Contact:
Hi Grant, I had an original one back in the eighties if you recall? Not sure if the TSR DJ is the same, but my rear floorboards were cut down, I.e. Only 5" long, to accommodate the exhaust.
-
- registered user
- Posts: 156
- Joined: Fri Jan 09, 2009 11:14 am
- Main scooter: Lambretta GP Monza 225
- Location: Livingston
- Contact:
Looking at SSCs web site, they seem to say as much, and indeed sell the modified rear runners. My DJ didn't have the tail can support, and eventually cracked around the main mount.
-
- registered user
- Posts: 445
- Joined: Thu Jun 20, 2013 10:10 pm
- Main scooter: lambretta af s type ts1
- Contact:
Back then Dave Webster made two expansions. One he called the 2 and a quarter inch muffler one and the other the vw tailpipe one. I had the vw one because that was for full panelwork and the one that there are copies of now was designed for no rear floor boards and possibly a trimmed offside panel.cheers, Speedy.
-
- registered user
- Posts: 1106
- Joined: Sun May 03, 2009 2:01 pm
- Main scooter: GP RS200 Iron barrel
- Contact:
You should only need to trim the rear footboard.
It should clear the panel. There is so little info on these pipes.
I did ask TSR about there's and they said they have had no issues and they have sold 100s of them.
It should clear the panel. There is so little info on these pipes.
I did ask TSR about there's and they said they have had no issues and they have sold 100s of them.
-
- registered user
- Posts: 1038
- Joined: Mon Jun 15, 2009 6:56 pm
- Main scooter: Lambretta Eibar Series 2
- Location: Bedford, UK
- Contact:
Noooooo Surely not??soosh wrote: I did ask TSR about there's and they said they have had no issues and they have sold 100s of them.
Got the same spiel from them myself on the issues ive had with the tsr evo!
Donnie.
-
- registered user
- Posts: 28
- Joined: Wed Dec 02, 2015 10:46 pm
- Main scooter: Indian GP RT 225
- Contact:
Sorry about the late response to my question I've been a little distracted with work the past couple of weeks. I was hoping that the TSR DJ might give a decent performance coupled with nostalgic looks. I was expecting to have to trim the rear foot board but the uncertainty of other clearance issues concerns me. It is for a full frame scooter and I want to keep the cutting and trimming to a minimum. Thanks everyone for taking the time to reply.
-
- registered user
- Posts: 1106
- Joined: Sun May 03, 2009 2:01 pm
- Main scooter: GP RS200 Iron barrel
- Contact:
Their website states you may need to trim the rear runner slightly which is normal. I'd say it will fit fine by the look of it.
I'd go for it at that price. Their site says dyno printout to be uploaded shortly but I think that's been on there for ages.
I'd go for it at that price. Their site says dyno printout to be uploaded shortly but I think that's been on there for ages.