Search found 102 matches
- Thu Jul 06, 2017 6:26 pm
- Forum: Lambretta Tech
- Topic: GP electronic kit..price/where
- Replies: 19
- Views: 5740
Re: GP electronic kit..price/where
If you are looking for the SIL kit then £149 at just lambretta
- Thu Jul 06, 2017 4:24 pm
- Forum: Lambretta Tech
- Topic: GP electronic kit..price/where
- Replies: 19
- Views: 5740
Re: GP electronic kit..price/where
Direct to Scooter Center in Germany, the BGM kits are in stock, €5 postage and always arrived within 48 hours, alternatively Just Lambretta, again great service and always competitive
- Mon Jul 03, 2017 7:17 pm
- Forum: Vespa Tech
- Topic: BGM 177 kit - really plug n play?
- Replies: 6
- Views: 4736
Re: BGM 177 kit - really plug n play?
Hi Mark, the Pinasco jetting on the std carb just needed the richer BE4 atomiser and main jet, I ran a R/H JL and that's was around 118-120
- Mon Jul 03, 2017 5:51 pm
- Forum: Vespa Tech
- Topic: BGM 177 kit - really plug n play?
- Replies: 6
- Views: 4736
Re: BGM 177 kit - really plug n play?
Hi Mark You can fit with the electric start but you do have to remove some material from the barrel, seems a bit drastic on a new barrel but it can run the gear ring I have ran 3 of these with both the 20 & 24 mm carbs, the std carb runs fine, just breaths better with the larger P200 unit A grea...
- Mon Jun 26, 2017 5:12 am
- Forum: Lambretta Tech
- Topic: What size & pitch is the s3 clutch nut?
- Replies: 2
- Views: 1301
Re: What size & pitch is the s3 clutch nut?
M14 X 1.50
- Sat Jun 17, 2017 5:41 pm
- Forum: Carburettor Set-ups
- Topic: Monza 225 phbh 30 and tsr evo exhaust
- Replies: 5
- Views: 3009
Re: Monza 225 phbh 30 and tsr evo exhaust
Hi Ben, the recommended slide for the Monza is much leaner, 50 slide
- Wed May 10, 2017 8:22 pm
- Forum: Vespa Tech
- Topic: Smallframe reed valve conversion
- Replies: 2
- Views: 1822
Smallframe reed valve conversion
Converting casings to reed valve, the principal is simple however does anyone have optimum dimensions on the sealing pad side, widthwise is fairly obvious with removing the width of the pad to the casings and blend, the question is on the height, how deep do you go for optimum results. Engine will b...
- Sun May 07, 2017 3:18 pm
- Forum: Show us yer Scoots!!
- Topic: GP Street Racer Build
- Replies: 26
- Views: 18969
Re: GP Street Racer Build
An update from changes over the winter, upgraded to the franspeed race which really releases the power of the kit, also struggled to jet the TMX in the mid range, tried every combination of jets and could not quite get it right. Changed to a VHSH as supplied with the Super Monza kits and setup was m...
- Fri May 05, 2017 5:33 am
- Forum: Lambretta Tech
- Topic: R1 Spring Dimensions
- Replies: 10
- Views: 3789
Re: R1 Spring Dimensions
Go on Lambretta upgrades website, they manufacture the specific spring to suit a Lambretta in multiple colours, you can get a 180lb off the shelf for £27
- Fri Apr 21, 2017 5:50 pm
- Forum: Lambretta Tech
- Topic: High tensile M7 end plate nuts & spring washers?
- Replies: 8
- Views: 3310
Re: High tensile M7 end plate nuts & spring washers?
Only ever used the MB ones, never had an issue and good value