scooterhelp is a good website to visit if you are just starting
its not a difficult job theres enough info at scooterhelp to do the job and more
good luck
Search found 1197 matches
- Sun Jan 29, 2012 8:33 pm
- Forum: Vespa Tech
- Topic: DIY PX200 engine rebuild
- Replies: 13
- Views: 6082
- Sun Jan 29, 2012 4:26 pm
- Forum: Lambretta Tech
- Topic: stepped carb rubber oko carb and mb manifold
- Replies: 5
- Views: 1991
Re: stepped carb rubber oko carb and mb manifold
sourced one at allens performance
for anyone interested its ref SR30 35mm one end and 40mm the other single round bead each end
i`ll speak to them tomorrow about price
for anyone interested its ref SR30 35mm one end and 40mm the other single round bead each end
i`ll speak to them tomorrow about price
- Sun Jan 29, 2012 2:09 pm
- Forum: Lambretta Tech
- Topic: stepped carb rubber oko carb and mb manifold
- Replies: 5
- Views: 1991
Re: stepped carb rubber oko carb and mb manifold
a dealer i try to avoid
- Sun Jan 29, 2012 10:41 am
- Forum: Lambretta Tech
- Topic: stepped carb rubber oko carb and mb manifold
- Replies: 5
- Views: 1991
stepped carb rubber oko carb and mb manifold
has anyone used a stepped rubber to fit a 30mm oko onto a mb amal/mikuni manifold for ts1 and if so where from
going to change carb but dont want to have to buy another mb manifold
manifold end would be 40mm id and carb end 35mm
cheers
going to change carb but dont want to have to buy another mb manifold
manifold end would be 40mm id and carb end 35mm
cheers
- Fri Jan 20, 2012 8:31 pm
- Forum: Lambretta Tech
- Topic: Fibreglass race seat
- Replies: 7
- Views: 2270
Re: Fibreglass race seat
hi i`ve just done one :- 1. Cut two plates about 125mm square out of 1mm mild steel and drilled a 9mm hole in each corner matching the four holes in the frame behind the petrol tank hole - the mounting position one plate for the top and one for the bottom (plate/seat/plate) to stop the fibreglass be...
- Tue Jan 10, 2012 11:38 am
- Forum: Vespa Tech
- Topic: heads up - italian p200 con rod kits half price
- Replies: 0
- Views: 798
heads up - italian p200 con rod kits half price
Allstyles have italian p200 con rod kits half price at £25.00 bargain
- Tue Jan 10, 2012 11:33 am
- Forum: Vespa Tech
- Topic: Help required
- Replies: 2
- Views: 992
Re: Help required
pm sent
- Mon Dec 26, 2011 11:51 am
- Forum: Vespa Tech
- Topic: Revolver/RZ/JL right hander exhaust runs lean?
- Replies: 3
- Views: 2230
Re: Revolver/RZ/JL right hander exhaust runs lean?
yes i had the same problem with a mates bike On a stock p200 motor following full rebuild - put a 125 main jet in it to run the motor in and - he pottered about town and got some miles on it - so off we went to Cleethorpes after about 45miles at about 55mph it holed the piston. No leaks anywhere whe...
- Sun Dec 11, 2011 5:54 pm
- Forum: Lambretta Tech
- Topic: crank shims are they necessary
- Replies: 3
- Views: 1496
Re: crank shims are they necessary
i`ve got an rd400 rodded indian webs no shims - its not in use yet but will going in a ts1 200 i`m going to build no shims used came out at 12.5+12.5(webs)+16(rod)+0.25(clearance) = 41.25 and fits okay No shims were used with this rod at the advise of a very experienced local crank builder he was co...
- Sun Nov 27, 2011 1:56 pm
- Forum: Lambretta Tech
- Topic: altering stroke on a crank
- Replies: 8
- Views: 2900
Re: altering stroke on a crank
be easier to by an eccentric crank pin