Dellorto UK, £10.34, cheers for the info!Boreham wrote:Cheers Gary, just need to track down a U16 needle.
Search found 102 matches
- Mon Jan 09, 2017 3:49 pm
- Forum: Carburettor Set-ups
- Topic: TS1 & VHSH 30
- Replies: 10
- Views: 5233
Re: TS1 & VHSH 30
- Mon Jan 09, 2017 9:33 am
- Forum: Carburettor Set-ups
- Topic: TS1 & VHSH 30
- Replies: 10
- Views: 5233
Re: TS1 & VHSH 30
Cheers Gary, just need to track down a U16 needle.
- Sun Jan 08, 2017 11:35 pm
- Forum: Carburettor Set-ups
- Topic: TS1 & VHSH 30
- Replies: 10
- Views: 5233
Re: TS1 & VHSH 30
Thanks Gary, can i just confirm the atomiser is a DQ267, the AQ is listed for the smaller PHBL carbs?
- Sun Jan 08, 2017 8:43 pm
- Forum: Carburettor Set-ups
- Topic: TS1 & VHSH 30
- Replies: 10
- Views: 5233
TS1 & VHSH 30
Tried several searches, anyone have a start point for this carb, the needle selection is endless!
TS1 with Franspeed race pipe.
TS1 with Franspeed race pipe.
- Sun Jan 08, 2017 2:19 pm
- Forum: Lambretta Tech
- Topic: Ultimate Engine Spec - Based on New Casa Case
- Replies: 35
- Views: 10883
Re: Ultimate Engine Spec - Based on New Casa Case
Hi Adam, I cannot comment on the specific DT kit however i have had a similar engine built by Pro porting, Monza barrel, 62x110 crank etc.... and the work involved to produce the quoted BHP was quite involved. The Monza barrel does have a similar port layout but the main comment i picked up by PP wa...
- Sat Dec 17, 2016 5:33 pm
- Forum: Lambretta Tech
- Topic: 4 or 5 Speed Feedback So Far?
- Replies: 13
- Views: 4473
Re: 4 or 5 Speed Feedback So Far?
I am runnung 2, from mid to full race tune, they are an amazing transformation.
The key is installing and setting up correctly, they get a bit of bad press but they are not a 'plug and play' if in doubt get a ptofessional to fit
The key is installing and setting up correctly, they get a bit of bad press but they are not a 'plug and play' if in doubt get a ptofessional to fit
- Sun Dec 04, 2016 7:16 am
- Forum: Vespa Tech
- Topic: Vespa small frame rear shock top mount
- Replies: 6
- Views: 1900
Re: Vespa small frame rear shock top mount
Hi Martin,
It sounds like you have the later shock with the integral thread, this has a rubber bush either side, the upper bush is a different shape, SIP part number 17185000
Cheers
It sounds like you have the later shock with the integral thread, this has a rubber bush either side, the upper bush is a different shape, SIP part number 17185000
Cheers
- Sat Oct 15, 2016 2:08 pm
- Forum: Carburettor Set-ups
- Topic: PWK jetting site
- Replies: 0
- Views: 1560
PWK jetting site
A useful site to calculate the combinations of PWK type jets and needles etc..
www.kyajet.com
www.kyajet.com
- Mon Oct 10, 2016 5:40 am
- Forum: Lambretta Tech
- Topic: TS1 200 carb advice needed
- Replies: 6
- Views: 2573
Re: TS1 200 carb advice needed
Hi,
I have ran a few on a Dellorto, usually a much richer needle X2 has been the key.
Cheers
I have ran a few on a Dellorto, usually a much richer needle X2 has been the key.
Cheers
- Sun Oct 09, 2016 6:39 am
- Forum: General Scooter Chat
- Topic: 90 degree mikuni throttle cable elbow
- Replies: 2
- Views: 2143
Re: 90 degree mikuni throttle cable elbow
I just use the Dellorto PH ones, same thread!