nice one Rob. coming over here this year ?Bilko wrote: Just taking a look at the engine now.
Search found 1226 matches
- Fri Apr 18, 2014 5:47 pm
- Forum: Lambretta Tech
- Topic: Speedo Cable Nut Size (Indian V Italian)
- Replies: 8
- Views: 2672
Re: Speedo Cable Nut Size (Indian V Italian)
- Tue Apr 01, 2014 8:21 pm
- Forum: Vespa Tech
- Topic: px rear hub oil seals
- Replies: 1
- Views: 1120
Re: px rear hub oil seals
was wondering this too..?
removed the internals from a broken early [external oil seal] casing
ok to fit everything into some LML casings ?
removed the internals from a broken early [external oil seal] casing
ok to fit everything into some LML casings ?
- Fri Mar 21, 2014 12:50 pm
- Forum: Vespa Tech
- Topic: crank for DR 130
- Replies: 1
- Views: 1474
crank for DR 130
90 with DR 130 fitted new crank needed. has electronic ignition currently using oe crank so thinking need 19/20 M10 on flywheel side, 51 stroke without spending huge amounts, the Mazzuchelli cranks seem to fit the spec, but these would not be my preferred crank to fit to a Lambretta, are they ok for...
- Sat Mar 08, 2014 3:53 am
- Forum: Lambretta Tech
- Topic: Lince 200 o-tuning à la mode fastfrog
- Replies: 285
- Views: 113033
Re: jet200 o-tuning à la mode fastfrog
good thread
did you look into other piston choices ?
I am going for an RD350 standard 64.00mm on mine, as they are a good piston, readily availble, and reasonably inexpensive.
did you look into other piston choices ?
I am going for an RD350 standard 64.00mm on mine, as they are a good piston, readily availble, and reasonably inexpensive.
- Sat Mar 08, 2014 3:45 am
- Forum: Lambretta Tech
- Topic: Any one fitted an Acewell?
- Replies: 17
- Views: 5557
Re: Any one fitted an Acewell?
...I was wondering if I could squeeze a battery between the the sides of my legshield spare wheel holder at the back between the panel ridge and back of the centre plate. would a battery this size be up to the job? get one of those nice boxes that Lloydiee does, fit a battery in there, and enjoy th...
- Sat Mar 08, 2014 3:42 am
- Forum: Lambretta Tech
- Topic: how do you replace the speedo outer cable ?
- Replies: 5
- Views: 2373
Re: how do you replace the speedo outer cable ?
put the speedo inner only up through the hole in the forks from the bottom, the "wrong way up" of course, so the hub end goes in first... then thread the outer over the top of this and down to the hub pull out the inner and feed it through the outer from the top... and put something round ...
- Sat Mar 08, 2014 3:32 am
- Forum: Lambretta Tech
- Topic: tyres ! what are your recommendations
- Replies: 49
- Views: 15776
Re: tyres ! what are your recommendations
Conti Race are just that. soft and very little tread... Conti Twist Road are good tyres, last ok, and grip in all conditions I used Schwalbe Racemans until all those scary photos I'd say the Contis are better, but possibly some auto-suggestion there... Yokahamas are good, just shame they don't have ...
- Tue Mar 04, 2014 9:32 pm
- Forum: General Scooter Chat
- Topic: Question 2. Punctureseal etc
- Replies: 20
- Views: 8230
Re: Question 2. Punctureseal etc
had a puncture last week, I use Ultraseal [now named PuntureSafe]. the tyre went down in 30 seconds, so was able to come to a controlled stop, but it would have been an instant blowout without it. I have replaced a tyre before, and found some of the sealant between the tube and tyre, it had done its...
- Tue Mar 04, 2014 12:34 am
- Forum: Lambretta Tech
- Topic: Ahh, those wires.... Help please
- Replies: 6
- Views: 1944
Re: Ahh, those wires.... Help please
can't tell much from those pictures
you need to get the rubber cover off, and see where the wires go...
is it bayonet bulb, or H4 type ?
you need to get the rubber cover off, and see where the wires go...
is it bayonet bulb, or H4 type ?
- Mon Mar 03, 2014 11:28 pm
- Forum: Lambretta Tech
- Topic: small block Mugello revamp
- Replies: 14
- Views: 3541
Re: small block Mugello revamp
thanks, but it's very much work in progress
adapting and learning as I go along, with huge guidance from Chris Sadd of C.S. Engineering
adapting and learning as I go along, with huge guidance from Chris Sadd of C.S. Engineering