Search found 169 matches

by hungdog
Sun Sep 24, 2017 6:32 pm
Forum: Vespa Tech
Topic: polini 210 carb options
Replies: 7
Views: 4650

Re: polini 210 carb options

:ugeek:
Im running a 30mm on the 210 malossi
running 55 pilot
40 slide
70 choke
x264 atomiser
125 main
x7 needle second clip
Your better off starting with a 130 main and working down..
by hungdog
Sun Sep 24, 2017 6:26 pm
Forum: Lambretta Tech
Topic: Jetting advice again
Replies: 6
Views: 2316

Re: Jetting advice again

:ugeek:
Im running a 30mm on the 210 malossi
running 55 pilot
40 slide
70 choke
x264 atomiser
125 main
x7 needle second clip
Your better off starting with a 130 main and working down..

Wrong post :mrgreen:
by hungdog
Sun Sep 24, 2017 12:33 pm
Forum: Vespa Tech
Topic: polini 210 carb options
Replies: 7
Views: 4650

Re: polini 210 carb options

28 or 30mm dellorto phbh
by hungdog
Sun Sep 17, 2017 11:51 am
Forum: Lambretta Tech
Topic: LCGB vs BLA
Replies: 13
Views: 5081

Re: LCGB vs BLA

Cheers for that
by hungdog
Sat Sep 16, 2017 6:25 pm
Forum: Lambretta Tech
Topic: LCGB vs BLA
Replies: 13
Views: 5081

Re: LCGB vs BLA

MaDMAn wrote: Sat Sep 16, 2017 2:56 pm
GeorgeS wrote: Fri Sep 15, 2017 5:18 pm It's the same thing.

Sent from my SM-G920F using Tapatalk

OK thanks. I also just seen that BLA do NOVA for £20 or a full registration service for a £80 fee, think I'll use them for the full monty.
Have you got a link to where it mentions the full registration service for a £80 fee.
by hungdog
Mon Aug 28, 2017 10:23 am
Forum: Paint & Bodywork Tech
Topic: Reframing
Replies: 4
Views: 3637

Re: Reframing

[quote=holty post_id=299025 time=1503863878 user_id=5321] the only way i could see that you could do it would be to build the scooter up on the old frame, mot and tax and insure it, i presume its registered, then swap the frames around, you can buy a bare lambretta vin tag and just stamp the number ...
by hungdog
Sun Aug 27, 2017 5:33 pm
Forum: Paint & Bodywork Tech
Topic: Reframing
Replies: 4
Views: 3637

Reframing

Does anyone know how you would go about " legally" reframing a scooter so to keep the original reg with DVLA, using a new hand built frame :ugeek:
by hungdog
Mon Aug 07, 2017 8:03 pm
Forum: Scooterotica Tuning & Maintenance Information
Topic: Cleaning small sieze marks barrel and piston?
Replies: 9
Views: 6657

Re: Cleaning small sieze marks barrel and piston?

You could also drill some 1/2 to 1mm holes in the piston directly beneath the bottom ring on the part where the heart caused the siezure. I have done this many times, it's a trick I got from a dirt bike tuning manual. It helps to keep the piston cool at the very point where it gets hot. Mike Never ...
by hungdog
Fri Aug 04, 2017 5:09 pm
Forum: Vespa Tech
Topic: Oil Seal Names
Replies: 2
Views: 1450

Re: Oil Seal Names

People seem to call the seals by different names, are the following correct combinations and are there any others? Tks Gary Crankshaft Engine/clutch/drive side seal Crankshaft ignition/Flywheel side seal Internal & External Rear Hub/Drive shaft seal Crankshaft Engine/clutch/drive side seal - De...
by hungdog
Tue Jul 18, 2017 5:54 pm
Forum: Vespa Tech
Topic: Px200 gear selector rod
Replies: 5
Views: 2278

Re: Px200 gear selector rod

:D Yep knew it was left handed thread and yes I've got a new rod and cruciform, so all is good ;)