Search found 325 matches
- Tue May 21, 2019 8:43 am
- Forum: Lambretta Tech
- Topic: Lambretta crank induction with Malossi MHR 221
- Replies: 34
- Views: 20253
Re: Lambretta crank induction with Malossi MHR 221
Brilliant effort ...no frame clearance issues ???
- Sat May 18, 2019 5:07 pm
- Forum: Lambretta Tech
- Topic: Wits end ...and past it
- Replies: 22
- Views: 10913
Re: Wits end ...and past it
OK tidy , I`ll check
- Sat May 18, 2019 8:57 am
- Forum: Lambretta Tech
- Topic: Wits end ...and past it
- Replies: 22
- Views: 10913
Re: Wits end ...and past it
I`m probably a bit late to the party ...but I hadn`t seen these before ??? https://www.jockeys-boxenstop.de/Final-drive-bearing-Jockeys-Boxenstop-Series-1-3-DL-GP Whats the idea ?? 2 shims instead of the old 1 and a dust felt pad under the retaining plate against the bearing ...??? Not that I want t...
- Sat May 18, 2019 8:40 am
- Forum: Lambretta Tech
- Topic: Wits end ...and past it
- Replies: 22
- Views: 10913
Re: Wits end ...and past it
Well , I agree , I`m annoyed that a pre-fitted bearing seal appears to be the wrong way around ..thats just ridiculous . I`ll look into getting a new rolf seal and some kind of guide to get the innner sealing lip facing downwards .
- Fri May 17, 2019 3:32 pm
- Forum: Lambretta Tech
- Topic: Wits end ...and past it
- Replies: 22
- Views: 10913
Re: Wits end ...and past it
Well, that`ll be about the 4th seal tried ...I used a double lip seal last time on the other MB bearing ....OK , when you fit the seal . does the inner lip sit up or down if that makes sense. I carefully ran my nail around the inner seal to poke it down on one seal , then span the inner race and the...
- Fri May 17, 2019 12:54 pm
- Forum: Lambretta Tech
- Topic: Wits end ...and past it
- Replies: 22
- Views: 10913
- Fri May 17, 2019 12:47 pm
- Forum: Lambretta Tech
- Topic: Wits end ...and past it
- Replies: 22
- Views: 10913
Re: Wits end ...and past it
Well that's a BGM bearing that came with the seal fitted ??? the spring is facing the gearbox ??
I think that's in correctly ?
Ive taken the mesh out of the oil filler plug so its just straight through ...so should be no pressure build up there
I think that's in correctly ?
Ive taken the mesh out of the oil filler plug so its just straight through ...so should be no pressure build up there
- Fri May 17, 2019 7:30 am
- Forum: Lambretta Tech
- Topic: Wits end ...and past it
- Replies: 22
- Views: 10913
Re: Wits end ...and past it
Heres some pics of the leak ......
- Thu May 16, 2019 12:36 pm
- Forum: Lambretta Tech
- Topic: Wits end ...and past it
- Replies: 22
- Views: 10913
Re: Wits end ...and past it
ha, no it doesn't seem silly mate ...yes definitely fitted the right way ....I have chucked old bearings ....and yes, my mate mentioned that they were preferable sometimes ...After I had chucked them out 
- Thu May 16, 2019 11:07 am
- Forum: Lambretta Tech
- Topic: Wits end ...and past it
- Replies: 22
- Views: 10913
Wits end ...and past it
:oops: Just fettling my TV200 rebuild and , for the life of me , cannot get the rear hub oil seal to stop leaking after a good run ...Its a TV2 casing and appears to be in good nick all round where the bearing sits so I`d obviously want to keep using that .... so far I have systematically replaced ....