Search found 495 matches
- Thu Sep 15, 2016 10:37 am
- Forum: Lambretta Tech
- Topic: Taffspeed Mk4 vs chiselspeeds ADS?
- Replies: 20
- Views: 11450
Re: Taffspeed Mk4 vs chiselspeeds ADS?
I currently use an early li 125 with 18x46 ...it has a very short first gear that gives it a good initiall punch...and still allows tall ratios in fourth..im on a 4 plate clutch still with strong springs and it copes fine..it revs out maybe 7.5 k through the gears..im getting 21bhp and 23ft.lbs of t...
- Mon Sep 12, 2016 11:49 pm
- Forum: Lambretta Tech
- Topic: Taffspeed Mk4 vs chiselspeeds ADS?
- Replies: 20
- Views: 11450
Re: Taffspeed Mk4 vs chiselspeeds ADS?
Sounds similar too one of my motors..225 mugello..boost ported.30phbh..ads 3...initially ran 4.4 gearing and i could get ut to pull...but its far more lively running 4.7 now
- Tue Aug 30, 2016 5:37 pm
- Forum: Lambretta Tech
- Topic: BGM clubman
- Replies: 18
- Views: 5263
Re: BGM clubman
Does sound an odd one...good bore clearance..rich jetting..no pinking..so i can see your train of thought for the pipe.... One more thing..after seizing do you remove the barrel?alluminium deposits could replicate a tight bore in places. Next for me id swap the pipe(altho im still not convinced) for...
- Tue Aug 30, 2016 4:54 pm
- Forum: Lambretta Tech
- Topic: BGM clubman
- Replies: 18
- Views: 5263
Re: BGM clubman
Are you experiencing any "pinking"under load?
- Tue Aug 30, 2016 3:29 pm
- Forum: Lambretta Tech
- Topic: BGM clubman
- Replies: 18
- Views: 5263
Re: BGM clubman
Those carb settings seem rich enough to keep it cool..i take it the avanti head was profiled for a yam piston?..
- Mon Aug 29, 2016 10:20 pm
- Forum: Lambretta Tech
- Topic: BGM clubman
- Replies: 18
- Views: 5263
Re: BGM clubman
Just to throw a spanner in the works....i run a very similar set up...225 muggello with reed..28 dellorto..bgm clubman..i do not have any heat issues The motor is a peach to ride....i like my bgm clubman If your siezing could it be your piston to bore clearance? Also after setting up 2 reed valve bi...
- Fri May 20, 2016 10:29 pm
- Forum: Lambretta Tech
- Topic: Bgm clubman ts1 28phbh jetting
- Replies: 0
- Views: 1104
Bgm clubman ts1 28phbh jetting
Built a mugello 225 reed with a 28phbh and bgm clubman..ive jetted it RICH ...saying that its ridable...trouble is ive done 10 miles and used half a tank of fuel :lol: ....so if any of you ts1 guys are using a 28 delly can you share your jetting. Im currently jetted rich at 266 atomizer X2 needle on...
- Mon May 09, 2016 10:53 pm
- Forum: Lambretta Tech
- Topic: piston id
- Replies: 7
- Views: 2634
Re: piston id
Done one with a tv rod and it needed a 2mm packer
- Mon May 09, 2016 10:14 pm
- Forum: Lambretta Tech
- Topic: piston id
- Replies: 7
- Views: 2634
Re: piston id
Or the third way
116 tv rod or 115 rd400 rod and keep near std port timings if required and no barrel mods
116 tv rod or 115 rd400 rod and keep near std port timings if required and no barrel mods
- Fri Jan 08, 2016 7:40 pm
- Forum: Lambretta Tech
- Topic: Jetting advice please
- Replies: 35
- Views: 13753
Re: Jetting advice please
Hi
I jetted up a 26 dellorto for a cast iron reed 200 set up using a gamma tech display to obtain good egt temps
Pilot 53
Atom av266
Needle x13 clip 2 from top
125 main
Hope this helps
Camel
I jetted up a 26 dellorto for a cast iron reed 200 set up using a gamma tech display to obtain good egt temps
Pilot 53
Atom av266
Needle x13 clip 2 from top
125 main
Hope this helps
Camel