Search found 24 matches
- Mon Jan 22, 2018 4:35 pm
- Forum: Welcome
- Topic: Hello everyone!
- Replies: 6
- Views: 2238
Re: Hello everyone!
ola Victor, welcome here !
- Thu Jan 18, 2018 4:53 pm
- Forum: Vespa Tech
- Topic: crankshaft locking up
- Replies: 11
- Views: 4087
Re: crankshaft locking up
when you install your casing gasket use some grease so when you have to split the cases, the gasket is still ok
- Wed Jan 17, 2018 7:56 pm
- Forum: Vespa Tech
- Topic: crankshaft locking up
- Replies: 11
- Views: 4087
Re: crankshaft locking up
the oil seal must be absolutely its case absolutely flat
- Wed Jan 17, 2018 7:40 pm
- Forum: Vespa Tech
- Topic: crankshaft locking up
- Replies: 11
- Views: 4087
Re: crankshaft locking up
No you can't, but a possible issue is that your oil seal on the main bearing is not pressed enough and then it can block the crank.
- Wed Jan 17, 2018 4:44 pm
- Forum: Vespa Tech
- Topic: crankshaft locking up
- Replies: 11
- Views: 4087
Re: crankshaft locking up
it could be one of the two masses that has moved if the crankshaft fell to the ground for example. Make sure the 2 masses of the crank are parallel. Use a comparator (crankshaft gauge ?) Sometime it can just be 1mm move and you just need a copper hammer without rebound http://www.kirikoo.net/images/...
- Wed Jan 17, 2018 8:24 am
- Forum: Vespa Tech
- Topic: Px Upgrade
- Replies: 3
- Views: 2217
Re: Px Upgrade
DR 177 is a very good kit. If you have a P200 crank you add a 5mm base plate to the cylinder. Cut a bit the crank and open the inlet, work on the piston. https://scontent-cdt1-1.xx.fbcdn.net/v/t1.0-9/21463022_10155107530541799_4488333127856466858_n.jpg?oh=2cda23e3aeba3ee331dcb804974ba150&oe=5AEE...
- Mon Jan 15, 2018 11:34 am
- Forum: Vespa Tech
- Topic: O-tuning V5A for my elder son (hot french recipe inside)
- Replies: 35
- Views: 15672
Re: O-tuning V5A for my elder son (hot french recipe inside)
Beau boulot Stéphane !
Et après rodage qu'est-ce que ça donne ce petit 50 ?
You should have try another exhaust on this engine, Polini are a bit limited
Et après rodage qu'est-ce que ça donne ce petit 50 ?
You should have try another exhaust on this engine, Polini are a bit limited
- Sat Jan 13, 2018 11:48 am
- Forum: Vespa Tech
- Topic: PX200 tuning
- Replies: 24
- Views: 11380
Re: PX200 tuning
No problem, I will.
- Fri Jan 12, 2018 7:46 pm
- Forum: Vespa Tech
- Topic: PX200 tuning
- Replies: 24
- Views: 11380
Re: PX200 tuning
I do all the engines myself Norrie. Performs for the moment I don't know; I finished the engine last week and my frame is not ready yet, still at the paint job. set up is on a SI 24/24 E : idle 60/160 air corrector 140 Atomiser BE1 Main jet 138 Slide n°4 old model without pocket. air filter p200 non...
- Fri Jan 12, 2018 8:58 am
- Forum: Welcome
- Topic: Hello from Froggyland !
- Replies: 11
- Views: 3227
Re: Hello from Froggyland !
Cheers hendy, I was answering to Simon B-Race tuning