Search found 71 matches
- Tue May 01, 2018 8:13 pm
- Forum: Lambretta Tech
- Topic: High Revving - air leak - failed gasket
- Replies: 15
- Views: 6257
Re: High Revving - air leak - failed gasket
Its strange you talk about this but I hadn't checked but what I have done today is to get a new carb - a 22mm upgrade kit with manifold and filter etc so I want to discount the carb thing once and for all (and it will be an upgrade from 18mm). I will therefore have to make sure everything is tighten...
- Tue May 01, 2018 4:52 pm
- Forum: Lambretta Tech
- Topic: High Revving - air leak - failed gasket
- Replies: 15
- Views: 6257
Re: High Revving - air leak - failed gasket
Unfortunately I suspect you are on the right lines. There is more to this than meets the eye. more updates as I find them.
- Tue May 01, 2018 10:49 am
- Forum: Lambretta Tech
- Topic: High Revving - air leak - failed gasket
- Replies: 15
- Views: 6257
Re: High Revving - air leak - failed gasket
Ok thats good to know. One item off the list then.
- Tue May 01, 2018 10:48 am
- Forum: Lambretta Tech
- Topic: High Revving - air leak - failed gasket
- Replies: 15
- Views: 6257
Re: High Revving - air leak - failed gasket
My suspicion is that the leaking at the exhaust manifold as has been like that for a while and needs a new gasket and a good clean up as a starter for ten. The only other improvement that I have done over the Winter is to fit a new flywheel and 12v kit. Once this was fitted the scooter has been fine...
- Tue May 01, 2018 10:40 am
- Forum: Lambretta Tech
- Topic: High Revving - air leak - failed gasket
- Replies: 15
- Views: 6257
Re: High Revving - air leak - failed gasket
Hi Paul, I checked that as well. It seems to be moving ok when I turn the throttle (it lifts the slide ok and the spring in the carb seems nice and strong too). Is there a way to lubricate it when its in situ anyway?
- Mon Apr 30, 2018 9:11 pm
- Forum: Lambretta Tech
- Topic: High Revving - air leak - failed gasket
- Replies: 15
- Views: 6257
High Revving - air leak - failed gasket
Hi All, As some of you may know I have a li150 which was bought last year. I haven't been out on it much so far - mainly due to poor weather and sorting bits on it (maybe a blessing in disguise if you read on). Its latest issue is a high revving engine on start up. i.e start it and it sounds like it...
- Thu Apr 19, 2018 9:11 am
- Forum: Lambretta Tech
- Topic: Panel Fittings - Series 3
- Replies: 11
- Views: 4758
Re: Panel Fittings - Series 3
Hi there, thats sounds more than plausible and I will investigate some quality replacement bits. Thanks for the advice!
- Wed Apr 18, 2018 8:47 pm
- Forum: Lambretta Tech
- Topic: Panel Fittings - Series 3
- Replies: 11
- Views: 4758
Re: Panel Fittings - Series 3
Thanks for the thoughts. I have the rollers and the original clips so even screwed in they flop which makes lining up tricky. However, I did try and clean everything up and regrease but when i turn the handle back the actual roller is kind of stuck and wont turn anymore for it to secure into place. ...
- Wed Apr 18, 2018 11:00 am
- Forum: Lambretta Tech
- Topic: Panel Fittings - Series 3
- Replies: 11
- Views: 4758
Panel Fittings - Series 3
Hi All, Quick question I want to replace the panel fittings on my S3. It currently has the roller type fittings but I checked on fleebay and there are 2 different types available i.e. - rollers v the rubber fitting. Can I use either of these for my slimline panels or do I have to use the roller type...
- Sat Apr 07, 2018 4:36 pm
- Forum: Lambretta Tech
- Topic: Exhaust spraying options
- Replies: 15
- Views: 6119
Re: Exhaust spraying options
Just done mine with this , https://uploads.tapatalk-cdn.com/20180403/94fae371686a3c46a013604536da254b.jpg £7 a can ! Couldn’t fit it in my oven so when it was touch dry put it back on and went for a good run to cure ! Sorted ! https://uploads.tapatalk-cdn.com/20180403/697329346a163037fbc619e6a708a1...