Search found 2588 matches
- Wed May 30, 2018 12:30 am
- Forum: Lambretta Tech
- Topic: Quattrini 125/150 Casing?
- Replies: 2
- Views: 2662
Re: Quattrini 125/150 Casing?
Not had any time to work on this kit recently so it's still a bare casing, albeit with welded casing.
- Wed May 30, 2018 12:26 am
- Forum: Lambretta Tech
- Topic: Quattrini 125/150 Casing?
- Replies: 2
- Views: 2662
Re: Quattrini 125/150 Casing?
Not sure what you mean by "mess with them"? The gaskets in the kit match the kit perfectly so trace the outline of the transfer from the gasket onto your casing and you'll see how much gasket face you've got. That's what I did on an Indian small block casing and the gasket face was around ...
- Tue Apr 10, 2018 11:32 pm
- Forum: Lambretta Tech
- Topic: Imola after market inlet manifold
- Replies: 11
- Views: 4848
Re: Imola after market inlet manifold
Yes, just fill it with JB weld.
- Tue Apr 10, 2018 11:30 pm
- Forum: Lambretta Tech
- Topic: AF 5 Speed Fitting Question
- Replies: 15
- Views: 6320
Re: AF 5 Speed Fitting Question
AF say that it generally sits about 1mm taller than your existing 4 speed gearbox, so if you've got a 2.4mm shim in there now you'll probably need around 1.4 for the 5 speed.
- Tue Apr 10, 2018 11:28 pm
- Forum: Lambretta Tech
- Topic: Which engine?
- Replies: 5
- Views: 2604
Re: Which engine?
Sell the GP with the Casa engine still in it. Keep the original Li engine and mothball it. Put a TS1 kit on the 200 block and fit that in the Li. Should you need to sell it you can return it to standard and sell the TS1 engine as a separate unit.
- Tue Apr 10, 2018 11:22 pm
- Forum: Tech FAQ
- Topic: readspeed 6 plate......
- Replies: 12
- Views: 7054
Re: readspeed 6 plate......
MB do a similar set up but works out about £70 more expensive. This but you still need to add plates & steels. https://www.lambrettaspares.com/spares/clutch-aand-chain-spares/lambretta-clutch-assembly-(kit)-47-tooth-(5-6-or-7-plate)-require-plate-kit-mb/mrb0759k.html That's probably been made re...
- Sat Apr 07, 2018 8:59 pm
- Forum: Lambretta Tech
- Topic: Imola after market inlet manifold
- Replies: 11
- Views: 4848
Re: Imola after market inlet manifold
I like the new MB manifold with attached rubber, good for frame clearance and panel clearance, it's got 4 holes though. https://www.lambrettaspares.com/spares/ ... 0871k.html
- Sat Apr 07, 2018 3:43 pm
- Forum: Lambretta Tech
- Topic: Imola after market inlet manifold
- Replies: 11
- Views: 4848
Re: Imola after market inlet manifold
Having never used V force reeds would these fit in here? My imola reed block shook itself apart and sent one of the screws into the cylinder ferkin everything I'm sure the tuning people get them to fit, with a bit of "fettling" of course. Most of the newer manifolds now only come with 3 h...
- Fri Apr 06, 2018 1:50 am
- Forum: General Scooter Chat
- Topic: LCGB AGM ref BLOA
- Replies: 245
- Views: 126534
Re: LCGB AGM ref BLOA
Look, I'm sick of seeing threads that I have no interest in whatsoever .........................................
........ so can someone please remove the Vespa sections.
........ so can someone please remove the Vespa sections.
- Fri Apr 06, 2018 1:44 am
- Forum: Lambretta Tech
- Topic: Exhaust spraying options
- Replies: 15
- Views: 6033
Re: Exhaust spraying options
What's the max temperature in "C" of those barbecue paint sprays? I was looking at some exhaust sprays that were 650 "C" but the Camcoat "Chrome" effect coating is about 900 from memory.