Search found 214 matches
- Sat Oct 05, 2013 6:02 am
- Forum: Vespa Tech
- Topic: t5 running lean
- Replies: 9
- Views: 3309
Re: t5 running lean
Matt, I think you are definately on the right track with the air leak. If you cant find anything else it might be the clutch side oil seal. Check the gear oil level. If it is empty fill it and see if it then smokes more than a pikey's truck!
- Fri Oct 04, 2013 12:48 pm
- Forum: Vespa Tech
- Topic: si carbs
- Replies: 30
- Views: 9926
Re: si carbs
I have not seen or heard a bad word about them. The one in mine has been in at least 3000 miles. Others I have done must be more by now. Mines a highly tuned Polini barrel so, I only put it in to try it and it went so well I don't want to take it out. With the 22 It's now pulling just over 8000 rpm ...
- Fri Oct 04, 2013 5:25 am
- Forum: Vespa Tech
- Topic: si carbs
- Replies: 30
- Views: 9926
Re: si carbs
Where did you hear that? Do you have yours or anyone else's picture of a worn one? If SIP and Worb5 both say they fit and they don't there must be plenty of examples out there
I could understand with the 21 tooth though!
I could understand with the 21 tooth though!
- Thu Oct 03, 2013 4:30 am
- Forum: Vespa Tech
- Topic: si carbs
- Replies: 30
- Views: 9926
Re: si carbs
The DRT one is straight cut teeth! The standard COSA2 Piaggio 22 tooth fits the 65 tooth ring gear. I think the 22 tooth is originally from a PX150
- Wed Oct 02, 2013 2:07 pm
- Forum: Vespa Tech
- Topic: si carbs
- Replies: 30
- Views: 9926
Re: si carbs
With or without the T5 4th, I have always fitted the 22 tooth clutch in any Malossi 210. They are tuned for power at the top of the rev range, at the expense of the torque. I have never fitted the 21 tooth with the 65, that would be a bit too slack for my liking. With the 22 tooth gear the same 210 ...
- Wed Oct 02, 2013 10:34 am
- Forum: Vespa Tech
- Topic: si carbs
- Replies: 30
- Views: 9926
Re: si carbs
Well if you are not going to change from the 210 kit then at least gear it to go properly. Once it is set up right that Scorpion exhaust will run really well on your set up. And you will be able to cruise at any speed, or just wide open
- Wed Oct 02, 2013 7:55 am
- Forum: Vespa Tech
- Topic: si carbs
- Replies: 30
- Views: 9926
Re: si carbs
The 210 kit even just bolted on without anything special done is a higher rpm kit. If you both wanted a cruiser or commuter you should have got a Polini 207, as it has far more torque than the Malossi. As you do both have the Malossi 210 you need to lower the gearing to let the Malossi high rpm do w...
- Tue Oct 01, 2013 10:59 am
- Forum: Vespa Tech
- Topic: si carbs
- Replies: 30
- Views: 9926
Re: si carbs
Why you not just buy the 22 tooth clutch? You could have it done in an hour!
You can still fit the T5 4th later on as well and have both
You can still fit the T5 4th later on as well and have both
- Mon Sep 30, 2013 11:13 am
- Forum: Vespa Tech
- Topic: si carbs
- Replies: 30
- Views: 9926
Re: si carbs
As far as I know the 22 tooth clutch is from a PX150 and can be used with any of the ring gears (65, 67or 68 tooth).
There is a bit more story on the SIP page
http://www.sip-scootershop.com/en/produ ... +_87473000
There is a bit more story on the SIP page
http://www.sip-scootershop.com/en/produ ... +_87473000
- Mon Sep 30, 2013 4:32 am
- Forum: Vespa Tech
- Topic: si carbs
- Replies: 30
- Views: 9926
Re: si carbs
It doesnt matter either way really. The PX200 4th gear is only about 1.5 mph longer. If you do already have a T5 4th and together with the 22 tooth clutch then the gearing will be perfect. Even with PX200 4th it will still be so much better. A decent expansion type exhaust (JL, Revolver, etc.) will ...