Search found 243 matches
- Thu Jun 18, 2020 11:01 am
- Forum: Lambretta Tech
- Topic: Effect of humidity and air temperature on carb performance
- Replies: 55
- Views: 25069
Re: Effect of humidity and air temperature on carb performance
i ran a pwk ,think it was a oko from scootrs,for years on a cast 200 top end,scorpion exhaust,didn't know much about jetting then,but put a 115 main in,think i was lucky,because i hit the sweet spot straight away,and thrashed it mercilessly,keeping up with the ts1's,never let me down,and did high fo...
- Tue Jun 09, 2020 11:30 pm
- Forum: Lambretta Tech
- Topic: yamaha conrod questions
- Replies: 16
- Views: 12133
Re: yamaha conrod questions
cheers,good tip about the neoprene strips
- Tue Jun 09, 2020 2:56 pm
- Forum: Lambretta Tech
- Topic: yamaha conrod questions
- Replies: 16
- Views: 12133
Re: yamaha conrod questions
have looked at various rods,and i think i am going to use the dt125ypvs rod as the big end bearing is 28mm o/d and i can get a rb spec bearing from af that is suitable,could'nt get conformation on what size big end bearings are on the other rods and didn't want to mess about sending them back. the ...
- Tue Jun 02, 2020 10:42 pm
- Forum: Lambretta Tech
- Topic: yamaha conrod questions
- Replies: 16
- Views: 12133
Re: yamaha conrod questions
did you run the ke175 rod with the supplied bearing with your ts1,a rb spec flat cage bearing at af is £12.50,but is 16mm wide,so possibly run that with .5mm shims,if the i/d will fit over the needle cage,cheers
- Sun May 31, 2020 10:23 am
- Forum: Lambretta Tech
- Topic: yamaha conrod questions
- Replies: 16
- Views: 12133
Re: yamaha conrod questions
cheers will have a look at the ktm rod if i change to a 30mm deck height piston. the ke 175d rod has a 15mm wide big end so can be used in standard width crank webs without machining them,and no shims,although not sure about what bearings are available in that width, my rb crank webs measure 12.1mm ...
- Fri May 29, 2020 1:45 pm
- Forum: Lambretta Tech
- Topic: yamaha conrod questions
- Replies: 16
- Views: 12133
Re: yamaha conrod questions
hi cheers warkton,do you know what model that rod is off can't find it cheers
- Fri May 29, 2020 12:14 pm
- Forum: Lambretta Tech
- Topic: yamaha conrod questions
- Replies: 16
- Views: 12133
Re: yamaha conrod questions
have looked at various rods,and i think i am going to use the dt125ypvs rod as the big end bearing is 28mm o/d and i can get a rb spec bearing from af that is suitable,could'nt get conformation on what size big end bearings are on the other rods and didn't want to mess about sending them back. the y...
- Thu May 28, 2020 2:05 pm
- Forum: Lambretta Tech
- Topic: Suzuki 190
- Replies: 18
- Views: 8957
Re: Suzuki 190
cheapest bang for bucks,200 barrell and piston,machine spigot to suit 150 casing,drill out one of the cylinder holes,and you can squeeze them on after fettling gaskets etc
- Thu May 28, 2020 12:15 pm
- Forum: Lambretta Tech
- Topic: yamaha conrod questions
- Replies: 16
- Views: 12133
yamaha conrod questions
hi chaps what is the best yamaha conrod to use,it will be going in standard ts1,i have some nice rb crank webs so going to have a go at building and it tigging the pin, dt125 ypvs has the correct big end pin and little end bearing 110 long 16mm wide big end 16mm little end rd 250 aircooled has same ...
- Mon Sep 09, 2019 12:47 pm
- Forum: Lambretta Tech
- Topic: ts1 30mm dellorto bgm clubman
- Replies: 3
- Views: 1926
Re: ts1 30mm dellorto bgm clubman
thanks for that,i am going to order a av268 and a 300 float valve and will get a few bigger jets probaly a 137 and a 140 and do some plug chops,are you running a 40 slide,as i found the 45 really cleaned up the running between 0 and 1/4 throttle,cheers