I thought it had fallen on stony ground.
For those who haven't noticed the 2nd page tab at the bottom it gives chain options.
Thanks Avantone
Search found 472 matches
- Thu Feb 26, 2009 8:34 pm
- Forum: Lambretta Tech
- Topic: Gearbox Ratio Calculator
- Replies: 2
- Views: 1605
- Fri Feb 13, 2009 10:12 pm
- Forum: Show us yer Scoots!!
- Topic: my last lammy
- Replies: 9
- Views: 3417
Re: my last lammy
Sad to hear that, Geoff. Never easy letting a good scoot go - especially after such a long time. Sorry for ya, mate. Gazza hi gary im hoping to get a lammy cutdown soon, matt black or army green :D btw...found a couple of pics from outside the wooden bridge pub 1981...i,ll email them to you when iv...
- Thu Feb 05, 2009 5:42 pm
- Forum: Lambretta Tech
- Topic: Using two regulators?
- Replies: 10
- Views: 3564
Re: Using two regulators?
Going back to the 70's when we had no money I had 3 spots on my old 6 volt series 2. I had no battery It was cut out of the loom, the rectifier was buggered and the connection for all cables was a 10amp common lighting junction box. I had mates who had up to 6 spots, OK the more you had the dimmer t...
- Tue Feb 03, 2009 7:36 pm
- Forum: Lambretta Tech
- Topic: running pathfinders without battery
- Replies: 92
- Views: 27380
Re: running pathfinders without battery
I know this has been done to death now and a battery is probably the easiest route, but it will charge slower than it is used with 2 spots. If you connect the spots direct to the BGM without a regulator and the lights are on you should be OK till you turn the lights off. Thats when the regulator cut...
- Tue Feb 03, 2009 5:43 pm
- Forum: Lambretta Tech
- Topic: SR Barrel
- Replies: 16
- Views: 5064
Re: SR Barrel
Thanks guys Yes I think it is one of the ones that we have seen so many problems with My understanding was that the ali casting was made with all the basic transfers and ports in the cast, the casting skimmed and the sleeve pushed in. My guy was told that the sleeve was pinned in??? At the end of th...
- Tue Feb 03, 2009 12:36 pm
- Forum: Lambretta Tech
- Topic: SR Barrel
- Replies: 16
- Views: 5064
Re: SR Barrel
Thanks Ian
Said club member calls it an SR barrel but it was quote a £110 ebay kit that ran fine until he dropped the piston ring.
Said club member calls it an SR barrel but it was quote a £110 ebay kit that ran fine until he dropped the piston ring.
- Tue Feb 03, 2009 8:36 am
- Forum: Lambretta Tech
- Topic: SR Barrel
- Replies: 16
- Views: 5064
Re: SR Barrel
I had an SR barrel bored out to 66mm, and it was fine. Only took it off after nearly 3000 miles to fit a Mugello. The problem may lie elsewhere. Apart from the din, does it run ok ? Yes but he is not brave enough to put in the miles. He found that his crank mag side bearing was shot with the inner ...
- Tue Feb 03, 2009 12:51 am
- Forum: Lambretta Tech
- Topic: SR Barrel
- Replies: 16
- Views: 5064
SR Barrel
Stupid question Guy at the club had said kit and dropped a ring that scored his barrel badly re board out 3 x over he says to clear the score Rebuilt but when its warms up sounds like the anvil chorus Been down the squish piston hitting the top, bottom, replaced his crank all bearings etc. no change...
- Sat Jan 31, 2009 7:47 pm
- Forum: Lambretta Tech
- Topic: Speedo probs
- Replies: 6
- Views: 2246
Re: Speedo probs
Take the drive end off the wheel and put an electric drill on the square inner cable run the drill in reverse and your speedo should work. It helps if your drill has a variable speed on it but see if its stable like that If it is it could be the worm drive in the hub, mine had a worn flat on it that...
- Fri Jan 23, 2009 5:24 pm
- Forum: Lambretta Tech
- Topic: Timing, Dial Gauge or Degree Disc
- Replies: 27
- Views: 9436
Re: Timing, Dial Gauge or Degree Disc
RinB If only my Physics teacher had taught us about gravitational pull using your avator, I may have taken more notice. As for TDC I have a 6inch nail in a roof joist in my shed. Crank in, the case put the flywheel on next and hang the hole thing up mark the magside casting and its done. I have neve...