How do you check the alignment by eye ?Daggs wrote:By eye.......................It's not let me down yet.
Search found 1110 matches
- Sat Dec 06, 2014 4:04 pm
- Forum: Lambretta Tech
- Topic: chain alignment
- Replies: 13
- Views: 4932
Re: chain alignment
- Wed Oct 15, 2014 4:51 pm
- Forum: Tech FAQ
- Topic: Mikuni TM28 Carb Setting
- Replies: 5
- Views: 2526
Re: Mikuni TM28 Carb Setting
Have a look through-carburettor set ups on this forum.Lots of set ups on there,I'm sure there will be something to match your set up.
- Tue Oct 14, 2014 11:01 am
- Forum: Lambretta Tech
- Topic: 12v ignition advice svp
- Replies: 10
- Views: 3778
Re: 12v ignition advice svp
Which make? I've turned this into a 'Who wants to be a millionaire' question in my head n it's driving me nannas. I was gonna take the plunge and get the variatronic but started thinking bout it and and the money involved and have got my nackers in a right twist. It's funny but when you look at thi...
- Sun Oct 05, 2014 4:50 pm
- Forum: Lambretta Tech
- Topic: Clutch clearance
- Replies: 7
- Views: 3100
Re: Clutch clearance
Sticky's manual only says 1mm as a minimum,this is to prevent clutch drag.If your clutch corks are the correct size-3.5mm thick and you say you are using the 1.5mm steels,there is no reason why the clutch should slip.The clutch springs are a pre determined length and the clutch pressure plate from t...
- Sun Oct 05, 2014 8:46 am
- Forum: Lambretta Tech
- Topic: spanish fat dampers
- Replies: 1
- Views: 1271
Re: spanish fat dampers
Try Buzzsolomoto in Halifax.Tel. 01422 385818
- Sat Oct 04, 2014 10:21 am
- Forum: Lambretta Tech
- Topic: Wired exhaust nuts
- Replies: 9
- Views: 3333
Re: Wired exhaust nuts
Use a chain guide tab washer.Cut it in half,drill the hole to m7,place over the stud,bend the cut part over the manifold and tighten the exhaust nut,then bend the tab against the nut.Do the same with the other one.essexgp wrote:Anybody know where i can get some wired exhaust nuts, tried evilbay but no luck
- Wed Oct 01, 2014 4:14 pm
- Forum: Lambretta Tech
- Topic: Fork Link Bushes
- Replies: 12
- Views: 4433
Re: Fork Link Bushes
Dont grind anything off the internal steel bush,it is supposed to be slightly longer than the plastic bush.The reason is as Donnie says,when tightened to the correct torque the internal steel bush is gripped and the fork links with the plastic bush are free to rotate.Just dont paint the inside of th...
- Sat Sep 27, 2014 6:15 pm
- Forum: Lambretta Tech
- Topic: 30mm dellorto disadvantage of fitting wire mesh under belmth
- Replies: 12
- Views: 5405
Re: 30mm dellorto disadvantage of fitting wire mesh under be
why not get a peice of gauze mesh and fit it without the bellmouth using a jubilee clip.
- Tue Sep 23, 2014 7:53 am
- Forum: Lambretta Tech
- Topic: gear alignment
- Replies: 8
- Views: 2776
Re: gear alignment
"There is approx 0.5mm misalignment between the gear cluster and loose gears ........." How do you know this ? Surely when built up the cluster and most of the loose gears are hidden behind the endplate. Engine on its side, measure displacement between teeth of cluster and loose gears. Ea...
- Mon Sep 22, 2014 3:25 pm
- Forum: Lambretta Tech
- Topic: gear alignment
- Replies: 8
- Views: 2776
Re: gear alignment
"There is approx 0.5mm misalignment between the gear cluster and loose gears ........."
How do you know this ? Surely when built up the cluster and most of the loose gears are hidden behind the endplate.
How do you know this ? Surely when built up the cluster and most of the loose gears are hidden behind the endplate.