Search found 1254 matches
- Mon Jul 11, 2016 9:46 pm
- Forum: Lambretta Tech
- Topic: ts1 jetting
- Replies: 6
- Views: 3744
Re: ts1 jetting
The smaller atomiser delivers less fuel so hopefully it will stutter on the bottom notch, then you can move the clip up one notch at a time till it runs clean.
- Mon Jul 11, 2016 6:33 pm
- Forum: Lambretta Tech
- Topic: ts1 jetting
- Replies: 6
- Views: 3744
Re: ts1 jetting
Being as your needle is on the top clip, I'd be inclined to try a 266 with the X7 on the bottom notch then move up one notch at a time till it runs clean. Pay attention to the plug but I will say that most TS1's have a stutter in that range just before it comes on song, some worse than others.
- Mon Jul 11, 2016 6:26 pm
- Forum: Lambretta Tech
- Topic: RB250 set up.
- Replies: 10
- Views: 6545
Re: RB250 set up.
On a tuned Ts1 with an NK I changed to a short 5th gear to keep it in the revs. Only lost a few mph top speed but much easier to ride.
- Mon Jul 11, 2016 6:20 pm
- Forum: Lambretta Tech
- Topic: Gearbox issue?
- Replies: 4
- Views: 2172
Re: Gearbox issue?
Slip the tie bar off the selector arm then remove the circlip on the swivel and lift off the post, then turn the twist grip towards 4 th. If it binds it may be the clutch cable trapping in the headset, easily done with some of the thicker nylon lined outers. If that's ok then it may be in the gearbo...
- Sun Jul 10, 2016 5:42 pm
- Forum: Lambretta Tech
- Topic: Outer rear brake cable.
- Replies: 7
- Views: 2795
Re: Outer rear brake cable.
When you fit the cable plate behind the choke lever it will probably be the right length and keep it away from the plug.
- Sat Jul 09, 2016 8:18 am
- Forum: Lambretta Tech
- Topic: Idle emulsifier
- Replies: 3
- Views: 1704
Re: Idle emulsifier
Thank you for the reply Adam , the carb had a B fitted from new so I tried the CD1 from a 34 carb that had a 36 idle and originally came off a TS1 so maybe I'm in the ball park.Logic says that a pilot in the 30's sounds small but obviously the motor says otherwise, certainly a PHBH would need a jet ...
- Fri Jul 08, 2016 10:20 pm
- Forum: Lambretta Tech
- Topic: Idle emulsifier
- Replies: 3
- Views: 1704
Idle emulsifier
I'm trying to set up the idle on a VHSH 30 flatslide as the 60 pilot fitted as standard is far too rich and have ended up with a 37 at the moment.I've emailed Eurocarb for advice regarding the emulsion tube that is fitted before the pilot but not received a reply yet and have spoken to a well known ...
- Fri Jul 08, 2016 10:01 pm
- Forum: Lambretta Tech
- Topic: probably another schoolboy error - no spark
- Replies: 28
- Views: 6886
Re: probably another schoolboy error - no spark
Trapped the stator wires or rubbed throught by the flywheel?
- Fri Jul 08, 2016 9:58 pm
- Forum: Tech FAQ
- Topic: SIP Tubeless Rim on Pepperpot Disc Hub - Fitting..
- Replies: 2
- Views: 2913
Re: SIP Tubeless Rim on Pepperpot Disc Hub - Fitting..
Can you post a pic?
- Thu Jun 30, 2016 6:23 am
- Forum: Lambretta Tech
- Topic: My nuts are leaking! Ooer :-)
- Replies: 10
- Views: 3666
Re: My nuts are leaking! Ooer :-)
I wouldn't use Threebond on the head but saying that I watched the Casa Team use it at Cadwell. I prefer Wellseal but various Loctite products can be used.