Search found 1741 matches
- Sat Sep 16, 2017 7:38 pm
- Forum: Lambretta Tech
- Topic: Engine removal
- Replies: 7
- Views: 2555
- Wed Sep 13, 2017 4:44 pm
- Forum: Lambretta Tech
- Topic: Stuck on engine decisions
- Replies: 14
- Views: 5585
Re: Stuck on engine decisions
there does seem to be a trend of going back to Lambretta "roots" i.e. keep standard but efficient. Messrs Innocenti did know one or two things after all.
- Mon Sep 04, 2017 6:00 pm
- Forum: Lambretta Tech
- Topic: ORIGINAL EXHAUSTS ID
- Replies: 3
- Views: 1947
Re: ORIGINAL EXHAUSTS ID
Ian
assuming its still got the muggie kit on it- what are you going to do with it? I've got a complete top end (cylinder; head; piston carb inlet; Dellorto 20mm carb etc for a TV175 s3) plus an original S3 IGM marked exhaust. Swap?
Chris
assuming its still got the muggie kit on it- what are you going to do with it? I've got a complete top end (cylinder; head; piston carb inlet; Dellorto 20mm carb etc for a TV175 s3) plus an original S3 IGM marked exhaust. Swap?
Chris
- Wed Aug 30, 2017 8:01 pm
- Forum: Lambretta Tech
- Topic: Plug gap
- Replies: 2
- Views: 1615
Re: Plug gap
running electronic I take it? Then 25 thou in old money should be fine.
- Tue Aug 29, 2017 12:25 am
- Forum: Lambretta Tech
- Topic: Inlet Manifold Gasket?
- Replies: 13
- Views: 4481
Re: Inlet Manifold Gasket?
Evening All, Planning to try a 22mm carb on my LIS150 in the not too distant future. Question is, do I need to fit an inlet manifold gasket, or can I get away with using gasket sealant? Also, if a gasket is recommended, is it OK to buy gasket paper and make my own? Sorry if it sounds a dumb questio...
- Mon Aug 28, 2017 5:51 pm
- Forum: Lambretta Tech
- Topic: Inlet Manifold Gasket?
- Replies: 13
- Views: 4481
Re: Inlet Manifold Gasket?
use a cereal box- grease up the end of the inlet manifold and press down. Cut round the ungreased areas.
Chris
Chris
- Sun Aug 27, 2017 9:23 pm
- Forum: Paint & Bodywork Tech
- Topic: Reframing
- Replies: 4
- Views: 3773
Re: Reframing
How much of the original frame do you need to use to maintain its original status? 3 feet; 2 feet; 6 inches; just the VIN area??
Chris
Chris
- Sat Aug 12, 2017 8:00 pm
- Forum: Lambretta Tech
- Topic: Steering Lock Help!
- Replies: 15
- Views: 5265
Re: Steering Lock Help!
will he need to push out the alloy cover on top of the lock as well to release the mechanism?
Chris
- Sat Aug 12, 2017 6:40 pm
- Forum: Lambretta Tech
- Topic: Steering Lock Help!
- Replies: 15
- Views: 5265
Re: Steering Lock Help!
it would appear that the odd key was OK to lock but not unlock...... you have 2 options (well 3 actually but..):- 1) get hold of the correct key and hope its OK 2) remove the headset top and take out the whole lock (not a hard job) or.... 3) you can force the lock and break it (and risk damaging the...
- Wed Aug 09, 2017 8:28 pm
- Forum: Scooterotica Tuning & Maintenance Information
- Topic: Cleaning small sieze marks barrel and piston?
- Replies: 9
- Views: 6927
Re: Cleaning small sieze marks barrel and piston?
heres one I did earlier- this has 3 holes near the base of the piston on the exhaust side. When the piston is travelling up and down the holes do not enter the exhaust area.