Search found 465 matches
- Tue Jul 28, 2015 2:43 am
- Forum: General Scooter Chat
- Topic: Scootering mag Apologies
- Replies: 69
- Views: 19362
Re: Scootering mag Apologies
If a copy happens to turn up here, it's a 1/2 day off work, get the beers in and make sure there are plenty of rizla's about. That way they can be read five times and still not remember what was in 'em , they never get boring...
- Mon Jun 08, 2015 11:30 pm
- Forum: Lambretta Tech
- Topic: Possible causes of rapid ring wear?
- Replies: 6
- Views: 3197
Re: Possible causes of rapid ring wear?
Had this happen once: installed a new kwaka jet ski piston set up. Rode to a rally(Summit point-about 185 miles from me) and wore out a set of rings. What happened was I was running with some small displacement engines, so was barely getting out of third most of the time. Was running a tad heavy on ...
- Mon Jun 01, 2015 5:07 am
- Forum: Lambretta Tech
- Topic: Piston Identification
- Replies: 12
- Views: 3996
Re: Piston Identification
Wonder what the tonnage was when it finally moved. 'Kin well done.
- Sun May 31, 2015 5:52 am
- Forum: Lambretta Tech
- Topic: Piston Identification
- Replies: 12
- Views: 3996
Re: Piston Identification
What magic potion did you use to get that unstuck and out?
- Thu Mar 05, 2015 3:01 am
- Forum: Lambretta Tech
- Topic: biggest bore on a lambretta
- Replies: 23
- Views: 8640
Re: biggest bore on a lambretta
What about a mico-lite barrel the German man did a few years ago?
- Thu Mar 05, 2015 2:44 am
- Forum: General Scooter Chat
- Topic: What The Fuel (WTF)!
- Replies: 20
- Views: 6114
Re: What The Fuel (WTF)!
Carbs have a high magnesium(or some such thing) level in the alloy. Perhaps that might be the issue.
Can still get 110 octane unleaded down the road, from the pump no less . Gotta luv the south
Can still get 110 octane unleaded down the road, from the pump no less . Gotta luv the south
- Thu Feb 12, 2015 11:06 pm
- Forum: General Scooter Chat
- Topic: Dave Webster
- Replies: 16
- Views: 12984
Re: Dave Webster
Best of luck Mr. Webster.
Your tuning book has had pride of place on the shelf many years now.
Darren
Your tuning book has had pride of place on the shelf many years now.
Darren
- Thu Feb 12, 2015 10:58 pm
- Forum: Lambretta Tech
- Topic: Running in new rings?
- Replies: 10
- Views: 4356
Re: Running in new rings?
I would say it would depend on how hard the metal is in your cylinder. If it's soft, they probably break in when kicking it over :o . if the metal is hard between 60-100 miles, blatting it as Bristolmod says. That way there'll be no lip at the top of the cylinder for the rings to catch on when you f...
- Sat Feb 07, 2015 6:01 pm
- Forum: General Scooter Chat
- Topic: And todays cockup is !???
- Replies: 104
- Views: 35583
Re: And todays cockup is !???
Even worse than wrong bearing in the flange... Have the factory Innocenti flywheel puller. Turns out the taper on the inside bolt of the puller works very well on indian cranks to mushroom the end of the crank out(where the threads are) if you use an impact butterfly on the bolt to get the job done ...
- Sat Feb 07, 2015 5:53 pm
- Forum: Lambretta Tech
- Topic: drive side plate screw HELP
- Replies: 20
- Views: 5837
Re: drive side plate screw HELP
Probably what the problem is with the allen heads being used is that high tensile are not being used, soft ones being put in there, allen key is harder than the allen bolt and next thing is a rounded bolt.