then again if she would of dropped while you were away you would only hear it for ever and ever and ever and ever .good luck with the birth .Search found 85 matches
- Sun Oct 04, 2009 9:14 pm
- Forum: Lambretta Tech
- Topic: Suspect GP rear hub
- Replies: 12
- Views: 3714
Re: Suspect GP rear hub
looks okay to me ,possibly had the wrong cone on it at one time or not tightened properly .should of gone to wickstead and left her taxi money then again if she would of dropped while you were away you would only hear it for ever and ever and ever and ever .good luck with the birth .
then again if she would of dropped while you were away you would only hear it for ever and ever and ever and ever .good luck with the birth .- Sat Sep 26, 2009 8:26 am
- Forum: Lambretta Tech
- Topic: fresco end can
- Replies: 1
- Views: 929
Re: fresco end can
ffs lads come on answer my question ?
where are all the clever fuckers this week ?
where are all the clever fuckers this week ?
- Sat Sep 26, 2009 8:22 am
- Forum: Lambretta Tech
- Topic: metal bits on magnetic drain plug ?
- Replies: 12
- Views: 4918
Re: metal bits on magnetic drain plug ?
yes dont ride it till youve had a look ,you will only wreck your engine totherwise .
- Thu Sep 24, 2009 5:09 pm
- Forum: Lambretta Tech
- Topic: fresco end can
- Replies: 1
- Views: 929
fresco end can
my fresco end can has gone tits up (af version )af aint got any in was told i could use a pm one with a bit of fettlin any ideas other than derivitin and repackin .
thanks andy
thanks andy
- Tue Sep 15, 2009 10:13 pm
- Forum: Lambretta Tech
- Topic: Small End Bearings Gap
- Replies: 11
- Views: 2593
Re: Small End Bearings Gap
bilko had exactly same thing on my ts1 (still in current engine )and i was told by af it dont matter as long as the big end is shimmed after all where is it going to go .my concern was about uneven wear but was told not to worry about it ,tis the first time ive ever had a piston like this .
andy
andy
- Wed Sep 02, 2009 9:12 am
- Forum: Show us yer Scoots!!
- Topic: just nuts & bolts
- Replies: 5
- Views: 2270
Re: just nuts & bolts
very nice darren ,clean tidy and straight 
- Wed Sep 02, 2009 9:01 am
- Forum: Lambretta Tech
- Topic: My RB20 bites the dust
- Replies: 24
- Views: 6791
Re: My RB20 bites the dust
look in the split in the conrod to see if any big end rollers are misaligned .been there twice 
- Sun Aug 30, 2009 9:46 am
- Forum: Lambretta Tech
- Topic: Sil wiring
- Replies: 4
- Views: 2464
Re: Sil wiring
page 221 for 6vlt or page 227 for 12vlt electronic ignition.
- Thu Jul 30, 2009 3:35 pm
- Forum: Lambretta Tech
- Topic: QA / QR Throttles
- Replies: 6
- Views: 3123
Re: QA / QR Throttles
yup same here but had a motoer x one on my taff years ago i thought that was slightly quicker because the wheel in the mounting was bigger used to sit on handlebars right where my mastercylinder is now did look cool though throttle going in through top of headstock. 
did look cool though throttle going in through top of headstock. - Thu Jul 30, 2009 3:28 pm
- Forum: Lambretta Tech
- Topic: Fitting legshield Toolbox..?
- Replies: 8
- Views: 7244
Re: Fitting legshield Toolbox..?
took horncast off loosened leggies pushed em forward a bit nut through, . drilled hole doulbe nutted .so if you only got two brackets you can go up or down as far as you want just get a measurement off lads from top off leggies to top of toolbox .