Search found 1154 matches
- Wed Apr 15, 2009 5:40 pm
- Forum: Carburettor Set-ups
- Topic: keihin jets
- Replies: 13
- Views: 4196
Re: keihin jets
Right, I think that may be an old ScootRS one with a different ie longer atomiser, and shorter main. It's also possible it's an even cheaper copy ____does it have a plastic slide as opposed to a chrome one? If it does, I had one of these and I think I've got some main jets for it somewhere. However,...
- Tue Apr 14, 2009 11:06 pm
- Forum: Carburettor Set-ups
- Topic: keihin jets
- Replies: 13
- Views: 4196
Re: keihin jets
Those "N" reference numbers are possibly Keihin factory numbers. I think that only the main importers, Allens, tend to use them. I have a v2 Mugello with a proper PM expansion and a bgm copy PWK28. I've seen needles from ScootRS with no markings in the past but I've never seen a Keihin pil...
- Sat Apr 11, 2009 12:36 am
- Forum: Lambretta Tech
- Topic: Advice on minor nip up.
- Replies: 25
- Views: 5861
Re: Advice on minor nip up.
..........., but I suppose if its done wrong you could do damage.... Yeah, I think that's the issue, this sort of information is useful to people who know exactly what they're doing______I just don't want your average rally going scooterist to think that subjecting all pistons to files, wet n dry, ...
- Fri Apr 10, 2009 10:24 pm
- Forum: Lambretta Tech
- Topic: Advice on minor nip up.
- Replies: 25
- Views: 5861
Re: Advice on minor nip up.
I'd suggest he probably did in the middle of a race meet when he'd just had a seize and didn't have a spare piston___________I doubt he'd recommend it as a best practice for sorting out this piston, on a road going scootdrunkmunkey6969 wrote:
Dave Webster used this tune and it certainly worked for him.
- Fri Apr 03, 2009 10:32 pm
- Forum: Carburettor Set-ups
- Topic: Jetting a PWK 30mm carb on a Mugello 225
- Replies: 10
- Views: 7204
Re: Jetting a PWK 30mm carb on a Mugello 225
............Is there a huge difference in jetting with an air filter and without? Yes, if you're going to run a filter, you need to jet it with the filter on. As you've no doubt discovered, performance varies a lot between no filter, and filter. I haven't tried one of the filters you link to, but t...
- Thu Apr 02, 2009 12:04 am
- Forum: Carburettor Set-ups
- Topic: Lambretta Carb Set-ups.....
- Replies: 77
- Views: 295682
Re: Lambretta Carb Set-ups.....
Engine: v2 Mugello 186, matched inlet and exhaust, 125 Special gearbox, 47/18 sprockets Carb: bgm Keihin copy PWK 28 with CamLam long RamAir filter through the panel. Pilot: 42 Needle; GJH- 2nd clip from top. Main; 128. Float set at 22mm. Timing: 18deg. Electronic. Exhaust: PM 25 expansion. Having r...
- Tue Mar 31, 2009 11:01 pm
- Forum: Carburettor Set-ups
- Topic: Jetting a PWK 30mm carb on a Mugello 225
- Replies: 10
- Views: 7204
Re: Jetting a PWK 30mm carb on a Mugello 225
If you compare the bgm needle with your JJH I reckon they'll be nearly the same, if not exactly the same. I think your way too rich on the needle. I'd keep the JJH in for the time being but change it to 2nd clip from top. Pilot, leave at 40, but if the starting from cold is not brilliant, maybe go u...
- Sat Mar 28, 2009 8:29 pm
- Forum: Standard Scoots & Restorations
- Topic: Race paint lettering
- Replies: 5
- Views: 3220
Re: Race paint lettering
Thanks for that link. Some very nice work on show on their site. A pity they're over 200 miles away from me.
Probably a good job though____I have to remember that I just wanted a bit of a spruce up, not a full custom paint job
Probably a good job though____I have to remember that I just wanted a bit of a spruce up, not a full custom paint job
- Fri Mar 27, 2009 5:47 pm
- Forum: Standard Scoots & Restorations
- Topic: Race paint lettering
- Replies: 5
- Views: 3220
Re: Race paint lettering
Just been to the local paintshop. He proposes using inverted graphics to use as stencils_____pretty obvious now I think about it
- Wed Mar 25, 2009 5:56 pm
- Forum: Standard Scoots & Restorations
- Topic: Race paint lettering
- Replies: 5
- Views: 3220
Race paint lettering
Thinking of getting a quote from a local custom bike shop to spruce up the paintwork on one of my scoots. This will involve some pearl white and gold metalflake over the already sapphire blue panels and legshields. Anyway, before I go and see them, just wondering whether any of you lads who've had r...