Hi .I bought mine from scooter emporium .It's one piece pressed steel.I did skim it with filler but overall a nice mudguard and a good fit.
You could leave it to get some surface rust then spray clear lacquer on it to stop it rusting any further
Dean
Search found 436 matches
- Wed Nov 25, 2015 9:52 pm
- Forum: Lambretta Tech
- Topic: Best remade front mudguard?
- Replies: 13
- Views: 5012
- Sat Nov 21, 2015 12:31 am
- Forum: Lambretta Tech
- Topic: BGM flywheel
- Replies: 14
- Views: 7130
Re: BGM flywheel
Hi. I have fitted 3 BGM stators to 3 different motors and had to send them all back as the centre stepped boss on the rear is machined incorrectly causing misalignment to the mag housing.one engine actually twisted the crank due to the flywheel touching the stator coils .I think they've modified th...
- Fri Nov 20, 2015 7:31 pm
- Forum: Lambretta Tech
- Topic: BGM flywheel
- Replies: 14
- Views: 7130
Re: BGM flywheel
Hi. I have fitted 3 BGM stators to 3 different motors and had to send them all back as the centre stepped boss on the rear is machined incorrectly causing misalignment to the mag housing.one engine actually twisted the crank due to the flywheel touching the stator coils .I think they've modified the...
- Wed Nov 18, 2015 11:51 pm
- Forum: Paint & Bodywork Tech
- Topic: lambretta frame jig work
- Replies: 12
- Views: 11602
Re: lambretta frame jig work
Do you have any rough dimensions for series 1/2 frames? I have to replace the centre stand strut on my ser 2 and my legshields are a bit wavy yet to try and sort it that way. I'd rather some kind of dimensions. I'm a welder fitter by trade amd set in my ways!! Lots of info out there for ser 3 but n...
- Sat Nov 14, 2015 7:34 pm
- Forum: Lambretta Tech
- Topic: Leak testing
- Replies: 26
- Views: 8927
Re: Leak testing
Some good advice on here .i would pressure test but only take flywheel/stator and side casing off if the pressure drops and there's no leaks around the top end.
Dean
Dean
- Fri May 29, 2015 7:14 pm
- Forum: Lambretta Tech
- Topic: Which Clutch ...........??
- Replies: 14
- Views: 6008
Re: Which Clutch ...........??
I've not fitted the centre spring in my lth clutch as I've heard rumours that they fall out and get trapped in the gearbox.I just put a little bit of sealer on the pressure plate to hold it in there securley.Dimitrios_231 wrote:A new LTH-7 yesterday,great clutch.
Dean
- Sat Apr 25, 2015 10:46 pm
- Forum: Lambretta Tech
- Topic: Which Clutch ...........??
- Replies: 14
- Views: 6008
- Thu Apr 16, 2015 11:47 am
- Forum: Lambretta Tech
- Topic: Lambretta Series 2 with Megasquirt EFI and 180w Igntion Syst
- Replies: 21
- Views: 9283
Re: Lambretta Series 2 with Megasquirt EFI and 180w Igntion
Hi Rich.what sort of fuel pressure would you estimate these to run at?how is stalling runart enrichment device worked out if its air cooled?is there a sensor under spark plug or in exhaust?do you run a stepper motor for the idle or just a cable effect?. Regards Dean There is an air temp sensor and ...
- Sun Apr 12, 2015 11:32 am
- Forum: Lambretta Tech
- Topic: Lambretta Series 2 with Megasquirt EFI and 180w Igntion Syst
- Replies: 21
- Views: 9283
Re: Lambretta Series 2 with Megasquirt EFI and 180w Igntion
At the moment the current BoM indicates a retail in thhow is region of £900. This is everything, ECU, Throtit's everythingump, injector, sub tank (I use the SV650 fuel pump because it is much neater for the plumbing but does ruel tank). It does require that the scooter is already converted to RS125...
- Sat Apr 04, 2015 8:52 am
- Forum: Paint & Bodywork Tech
- Topic: Ali welding
- Replies: 11
- Views: 7002
Re: Ali welding
I'm no expert but I'm looking to buy a tig set at some point and I've recently spoken to a company called R TECH in Gloucestershire ..you'd need at least 200amp or above and would he looking to spend around £1000-£1500.keep away from cheap crap on ebay too.
Dean
Dean