Search found 1155 matches
- Tue May 17, 2011 9:53 pm
- Forum: Show us yer Scoots!!
- Topic: JUST BUILDING A RAT CHOP
- Replies: 88
- Views: 22656
Re: JUST BUILDING A RAT CHOP
Think you just clicked on the wrong code.
Think it should be the fourth line of text.
- Tue May 17, 2011 9:24 pm
- Forum: Lambretta Tech
- Topic: Stage four cylinder + Eibar 200 head
- Replies: 4
- Views: 2004
Re: Stage four cylinder + Eibar 200 head
I have used a Spanish 200 head on a stage 4 indian barrel and it ran fine... I also used the Spanish head on a Rapido 200, That was so I could lower the compression ratio a little compared to the 9.1-1 ratio skimmed head that I had used... Again it ran well and allowed it to rev a little higher on.....
- Mon Mar 28, 2011 6:42 pm
- Forum: Lambretta Tech
- Topic: 200 engine in a series 2??
- Replies: 8
- Views: 2524
Re: 200 engine in a series 2??
You will need to fit an LI/SX clutch bell as you can't fit a brass plunger for the GP clutch bell to the LI side case, only the GP side case has this to my knowledge.
but other than what's been mentioned in the thread so far I think that's about it...
Best of luck,
Mark...
but other than what's been mentioned in the thread so far I think that's about it...
Best of luck,
Mark...
- Sun Mar 27, 2011 10:29 pm
- Forum: Lambretta Tech
- Topic: Building a crank D.I.Y
- Replies: 9
- Views: 2183
Re: Building a crank D.I.Y
Yes I meant Conrod, it just dosnt read like that now you've pointed it out.
As for trueing crankshafts... A lot of luck.... and a big brother that knows what he's doing is a major plus...
As for trueing crankshafts... A lot of luck.... and a big brother that knows what he's doing is a major plus...
- Sun Mar 27, 2011 6:41 pm
- Forum: Lambretta Tech
- Topic: 200 engine in a series 2??
- Replies: 8
- Views: 2524
Re: 200 engine in a series 2??
You will have to open out the holes to take 8mm studs & remove some alloy from the sidecase to fit the bracket for the JL exhaust.smoore-gt225 wrote:hi thanks for replies so if i put on a series 2 chaincase does a jl3 exhaust bracket fit on or will i have to drill out the holes
cheers steve
- Sat Mar 26, 2011 8:01 pm
- Forum: Lambretta Tech
- Topic: Hmm......... nice !
- Replies: 38
- Views: 10031
Re: Hmm......... nice !
You were too quick for me Soulsurfer...
What I wondered was. Would it need more machining depending on the choice of pipe???
What I wondered was. Would it need more machining depending on the choice of pipe???
- Sat Mar 26, 2011 7:56 pm
- Forum: Lambretta Tech
- Topic: Hmm......... nice !
- Replies: 38
- Views: 10031
Re: Hmm......... nice !
And the cut away is for the exhaust?
Or is t just for the frame tube?
Or is t just for the frame tube?
- Sat Mar 26, 2011 7:50 pm
- Forum: Lambretta Tech
- Topic: 200 engine in a series 2??
- Replies: 8
- Views: 2524
Re: 200 engine in a series 2??
Yes it pretty much is but the series 2 kickstart will most likely miss the rubber stop. I fitted the series 2side case to mine and opened out the stud holes and carefully milled out the alloy around the studs on the side case to take a Taffspeed exhaust bracket. The casing looks as it should but the...
- Sat Mar 26, 2011 7:43 pm
- Forum: Lambretta Tech
- Topic: Lambretta End Plate Stud Failure?
- Replies: 5
- Views: 3385
Re: Lambretta End Plate Stud Failure?
Like the idea of upside-down nylocks.!
if using spring washers on the endplate studs the spring washers should only be used once and then replaced if you want to get the best out of them.
if using spring washers on the endplate studs the spring washers should only be used once and then replaced if you want to get the best out of them.
- Sat Mar 26, 2011 7:01 pm
- Forum: Lambretta Tech
- Topic: Building a crank D.I.Y
- Replies: 9
- Views: 2183
Re: Building a crank D.I.Y
I've had cranks built for me by Grampians in the Past, but now there are many quality cranks with 110 rod kits fitted it's less bother to just buy one of these. I have access to a press, centres & V blocks, copper mallets wedges clamps & gauges for truing up after. But I still buy ready made...