Search found 361 matches
- Tue Dec 06, 2016 7:17 pm
- Forum: Paint & Bodywork Tech
- Topic: Bare metal pre paint rust worry
- Replies: 14
- Views: 6757
Re: Bare metal pre paint rust worry
This time of year any bare metal will start to rust very quickly with the damp cold air , it would be best to prime straight away .
- Wed Nov 30, 2016 3:05 pm
- Forum: General Scooter Chat
- Topic: Courier or Post Office/Parcelforce for engine?
- Replies: 19
- Views: 5027
Re: Courier or Post Office/Parcelforce for engine?
I use parcel2go.com its usually around £20 without insurance which ive never added , its usually collected by UPS and delivered within 2 days,UK delivery, a complete engine packaged very well weighs around 35kg , make sure oil is drained out, the only problem is they dont except engines so list it a...
- Mon Nov 28, 2016 1:11 pm
- Forum: Lambretta Tech
- Topic: Ultimate Engine Spec - Based on New Casa Case
- Replies: 35
- Views: 10910
Re: Ultimate Engine Spec - Based on New Casa Case
I fail to make sence of anything said above , if you want a road tune /touring motor then thats what you build , if however you want a high spec , high revving quick/fast race type motor built for 1/4 mile sprinting , top speed events , circuit racing or just thrashing about then that is something t...
- Sat Nov 19, 2016 11:53 pm
- Forum: Lambretta Tech
- Topic: Drive side bearing
- Replies: 9
- Views: 3302
Re: Drive side bearing
You need to make sure the halite washer is being compressed by the seal plate. yes very important , you will find the gaskets come in various thicknesses from 0.5mm up to 1mm , im just rebuilding a couple of spanish engines and they will only seal with 1mm hallite using the original plates , with s...
- Sat Nov 19, 2016 9:34 pm
- Forum: Lambretta Tech
- Topic: Drive side bearing
- Replies: 9
- Views: 3302
Re: Drive side bearing
You need to make sure the halite washer is being compressed by the seal plate. yes very important , you will find the gaskets come in various thicknesses from 0.5mm up to 1mm , im just rebuilding a couple of spanish engines and they will only seal with 1mm hallite using the original plates , with s...
- Fri Nov 18, 2016 3:28 pm
- Forum: Lambretta Tech
- Topic: Grinding Bits
- Replies: 9
- Views: 3220
Re: Grinding Bits
It might be worth using demel type small sanding drums , you will be less likely to take to much off or slip and cause damage if this is your first attempt at this, if you planning on taking quite a bit off then the burr cutters will be better.
- Wed Nov 09, 2016 9:26 pm
- Forum: Lambretta Tech
- Topic: Bent fork Spring rods?
- Replies: 4
- Views: 2054
Re: Bent fork Spring rods?
gone over a nice pothole ?
- Wed Oct 26, 2016 8:27 pm
- Forum: Dealer News, Innovations & Products
- Topic: Fork link damper conversion
- Replies: 11
- Views: 9826
Re: Fork link damper conversion
i also have had a few sets done including some for my own scoot , again great service.
- Wed Oct 12, 2016 12:24 pm
- Forum: Lambretta Dyno Graphs
- Topic: RAPIDO 42 BHP to start with.
- Replies: 51
- Views: 51758
Re: RAPIDO 42 BHP to start with.
congrats - nice work at the engine! Beware of the machined flywheel it is tent to crack at the three bridges. A reason why I changed to a variotronic and get off the fan and the extra ring that is press on, as well as weld the rivets. The weight will be 979g. KR Lutz Hi Lambretta Lutz, this is an e...
- Mon Oct 10, 2016 8:59 pm
- Forum: Lambretta Tech
- Topic: Mito Lambretta Hydraulic Disc Brake Kit...
- Replies: 3
- Views: 2310
Re: Mito Lambretta Hydraulic Disc Brake Kit...
I have the mito single, had it over 2 years and very impressed with the stopping power and does look great, i also have the lth/mmw larger billet master cylinder as it uses the stage6 4 piston caliper , i was after another mito earlier this year but af rayspeed were struggling to get any in stock .