hi thanks for replies think it will be to much hassle was thinking of getting better lights etc
anyway what about going down the bgm route is that better than the standard 5 pin reg
cheers steve
Search found 182 matches
- Mon Aug 22, 2016 9:40 pm
- Forum: Vespa Tech
- Topic: vespa t5 and wassel
- Replies: 4
- Views: 1785
- Mon Aug 22, 2016 1:04 pm
- Forum: Vespa Tech
- Topic: vespa t5 and wassel
- Replies: 4
- Views: 1785
vespa t5 and wassel
Hi can you fit a wassel reg to fully dc a t5 if so do you have
to do the extra wire in the stator etc
cheers steve
to do the extra wire in the stator etc
cheers steve
- Sat Aug 20, 2016 8:50 pm
- Forum: Vespa Tech
- Topic: t5 classic paint
- Replies: 8
- Views: 3339
Re: t5 classic paint
thanks for replies and it is ford signal yellow
cheers again steve
cheers again steve
- Thu Aug 18, 2016 7:58 am
- Forum: Vespa Tech
- Topic: t5 classic paint
- Replies: 8
- Views: 3339
t5 classic paint
Hi can anyone identify for me the colour of this t5 classic
i know its yellow but whats the paint code etc and where i could possibly get it from
cheers steve
i know its yellow but whats the paint code etc and where i could possibly get it from
cheers steve
- Tue Aug 09, 2016 6:09 pm
- Forum: Vespa Tech
- Topic: 24/24 carb settings
- Replies: 11
- Views: 4600
Re: 24/24 carb settings
Hi guys just built a px motor polini 180 kit matched to casings 60mmlongstroke mazz crank drt reed valve under standard airbox polini induction kit with foam filter revolver exhaust anybody have a ball park figure for jetting etc just to get me up and running HI can I ask where you got a reedvalve ...
- Sun Jul 17, 2016 10:36 pm
- Forum: Lambretta Tech
- Topic: ts1 jetting
- Replies: 6
- Views: 3751
Re: ts1 jetting
The smaller atomiser delivers less fuel so hopefully it will stutter on the bottom notch, then you can move the clip up one notch at a time till it runs clean. Hi Wack 63 I finally got round to playing with scoot today and could not get it to run right with any combination in the end it was the duc...
- Mon Jul 11, 2016 8:33 pm
- Forum: Lambretta Tech
- Topic: ts1 jetting
- Replies: 6
- Views: 3751
Re: ts1 jetting
Hi thanks for replies Being as your needle is on the top clip, I'd be inclined to try a 266 with the X7 on the bottom notch then move up one notch at a time till it runs clean. Pay attention to the plug but I will say that most TS1's have a stutter in that range just before it comes on song, some wo...
- Sun Jul 10, 2016 5:56 pm
- Forum: Carburettor Set-ups
- Topic: ts1 jetting
- Replies: 1
- Views: 2098
Re: ts1 jetting
posted in wrong section cant find a delete button 
- Sun Jul 10, 2016 5:45 pm
- Forum: Lambretta Tech
- Topic: ts1 jetting
- Replies: 6
- Views: 3751
ts1 jetting
Hi I cant seem to get rid of stuttering four stroking, plug chops etc all ok, its just in the mid range and I cant pull it through it unless I knock it down a gear and rev it out before I change up ts1 with a delly 30mm phbh av268 atomiser 138 main x7 needle top clip 55 idle 350 float timing at 18 d...
- Sun Jul 10, 2016 5:39 pm
- Forum: Carburettor Set-ups
- Topic: ts1 jetting
- Replies: 1
- Views: 2098
ts1 jetting
Hi I cant seem to get rid of stuttering four stroking, plug chops etc all ok, its just in the mid range and I cant pull it through it unless I knock it down a gear and rev it out before I change up ts1 with a delly 30mm phbh av268 atomiser 138 main x7 needle top clip 55 idle 350 float timing at 18 d...