Search found 795 matches
- Sat Oct 31, 2015 7:16 pm
- Forum: Lambretta Tech
- Topic: Engine test bed wiring
- Replies: 7
- Views: 2853
Re: Engine test bed wiring
Red white and green off the stator to the cdi , thr yellow is the lighting wire which normally goes to the reg .
- Sat Oct 31, 2015 7:13 pm
- Forum: Lambretta Tech
- Topic: Is there a correct sequence.....?
- Replies: 7
- Views: 3275
Re: Is there a correct sequence.....?
I tighten the spindle nuts then the third nut , but this shouldnt make any difference if you wheel is leaning , I think you need to look at you springs , rods and buffers.
- Sat Oct 31, 2015 7:07 pm
- Forum: Lambretta Tech
- Topic: How long....?
- Replies: 3
- Views: 1807
Re: How long....?
I do a leak test as soon as its built , before its been run .
- Sat Oct 24, 2015 11:00 am
- Forum: Lambretta Tech
- Topic: Lambretta Leeds chain guide
- Replies: 3
- Views: 1956
Re: Lambretta Leeds chain guide
Is that the red one ? A copy/ rip off of Richard Taylors design ?
- Wed Oct 21, 2015 9:58 pm
- Forum: Lambretta Tech
- Topic: Gearbox end plate
- Replies: 3
- Views: 2129
Re: Gearbox end plate
Yep ive done the above , I just used a couple of rollers fron a mag bearing nu2205 , from memory the end plate pins /dowels are 7mm and the rollers are 8mm . Line up the endplate and bolt down , then drill through the endplate and into the alloy, the rollers are a bit shorter than the original pins ...
- Wed Oct 21, 2015 7:25 pm
- Forum: Lambretta Tech
- Topic: Oily side panels a solution?
- Replies: 19
- Views: 6011
Re: Oily side panels a solution?
Dunno ? ....but could you get me a left handed screw driver please , ive lost mine10 inch Terror wrote:What have I started?
- Tue Oct 20, 2015 3:33 pm
- Forum: Lambretta Tech
- Topic: Oily side panels a solution?
- Replies: 19
- Views: 6011
Re: Oily side panels a solution?
Ive been looking for bubbles , sparks and tartan paint since iwas sent to get some as an apprentice 33 years ago coldnt find them anywhere ?? I didfind a long weight though 
- Sat Oct 17, 2015 10:10 pm
- Forum: Lambretta Tech
- Topic: Oily side panels a solution?
- Replies: 19
- Views: 6011
Re: Oily side panels a solution?
Good idea
never heard of heat resistant heat shrink before
lol
never heard of heat resistant heat shrink before
lol- Sat Oct 10, 2015 10:25 am
- Forum: General Scooter Chat
- Topic: Digital speedo fitted to drum set up
- Replies: 1
- Views: 1369
Re: Digital speedo fitted to drum set up
Yes you can .
Sip ones run off either the speedo cable or a magnetic pick up .
Gamma tech speedo are the bo****ks, but dont fit in the std speedo space ..............yet
Imo magnetic pick up is the better and more accurate and reliable of the two methods.
Sip ones run off either the speedo cable or a magnetic pick up .
Gamma tech speedo are the bo****ks, but dont fit in the std speedo space ..............yet
Imo magnetic pick up is the better and more accurate and reliable of the two methods.
- Sat Oct 10, 2015 10:19 am
- Forum: Paint & Bodywork Tech
- Topic: Satin black paint job
- Replies: 6
- Views: 4374
Re: Satin black paint job
Black board paint is matt :) Yes you can get satin clear coat . I used black base with a satin clear coat on mine , one thing I hadnt considered though was with a gloss clear coat , any blemishes can be cut back and polished out .....cant do that with satin ...or matt for that matter , as any polish...