Search found 268 matches
- Wed Mar 05, 2014 6:19 pm
- Forum: Lambretta Tech
- Topic: Cross hatching
- Replies: 12
- Views: 3656
Cross hatching
having used a 3legged glaze buster on the barrel to take some light score marks out I have then checked the rings down the bore from top to bottom with correct ring clearance, i shone a light down the bore at the same time just to see if there was any light between ring and bore but all is ok so wha...
- Tue Feb 11, 2014 9:20 am
- Forum: Lambretta Tech
- Topic: pistons ??
- Replies: 2
- Views: 1508
Re: pistons ??
Thanks very much for that Rosscla
- Sun Feb 09, 2014 5:31 pm
- Forum: Lambretta Tech
- Topic: pistons ??
- Replies: 2
- Views: 1508
pistons ??
Please could someone tell me that when you look for a piston you get std,++,+ ,or _ , and i`m only looking for
66mm one for the 2 barrels i have acquired.they were of scooter restoration site
66mm one for the 2 barrels i have acquired.they were of scooter restoration site
- Tue Dec 31, 2013 7:39 pm
- Forum: Lambretta Tech
- Topic: piston ring peg
- Replies: 4
- Views: 1886
Re: piston ring peg
thanks for the replys,as for assuming a cheap piston which is prob correct but I`ve had the same troubles with a peg coming out of an asso piston and messing up my top end up after it had been sorted to 14.65bhp..
and also it is the original piston
and also it is the original piston
- Mon Dec 30, 2013 3:56 pm
- Forum: Lambretta Tech
- Topic: piston ring peg
- Replies: 4
- Views: 1886
piston ring peg
just rebuilding a mates scooter gp200 engine and noticed that the top ring pin is no were near out as far as the bottom ring pin.
what options do I have ? new hole put in,Or a new pin put in, Its just a std indian top end.
Ta Paul
what options do I have ? new hole put in,Or a new pin put in, Its just a std indian top end.
Ta Paul
- Sun Dec 29, 2013 10:14 pm
- Forum: Tech FAQ
- Topic: port map of std gp200
- Replies: 0
- Views: 1195
port map of std gp200
does anybody have a map of a std 200 gp with all dims on please as i just
want to check them against a couple of barrels i`ve acquired..
Ta Paul
want to check them against a couple of barrels i`ve acquired..
Ta Paul
- Sun Dec 29, 2013 6:31 pm
- Forum: Lambretta Tech
- Topic: glaze busting cylinder
- Replies: 4
- Views: 1862
Re: glaze busting cylinder
thanks all for the reply`s
- Sat Dec 28, 2013 7:07 pm
- Forum: Lambretta Tech
- Topic: glaze busting cylinder
- Replies: 4
- Views: 1862
glaze busting cylinder
What is the best solution to use with the three legged buster on the cylinder,
i`ve heard of some people using paraffin mixture.
Ta Paul
i`ve heard of some people using paraffin mixture.
Ta Paul
- Thu Dec 19, 2013 11:20 am
- Forum: Tech FAQ
- Topic: silencer packing
- Replies: 5
- Views: 1913
Re: silencer packing
hello mr series 2,got what you got for my end can and works great thanks for that
- Mon Dec 16, 2013 4:30 pm
- Forum: Lambretta Tech
- Topic: My Vega stoped going flat out... Any thoughts?
- Replies: 8
- Views: 3543
Re: My Vega stoped going flat out... Any thoughts?
just check that the handle part of the petrol tap what you get hold of to turn it on is not slipping on the shaft,it happened to me last year thought i`d turned it on to full but when going down the road for about 600yrds it stopped wondered what was the cause was by that time it had filled up again...