Search found 348 matches
- Sun Jun 23, 2013 11:42 am
- Forum: Lambretta Tech
- Topic: Sip digi speedo mph not working ?
- Replies: 1
- Views: 858
Re: Sip digi speedo mph not working ?
Check that the cable square drive is fully inserted in the speedo Simon. Sounds like it's just catching on the edge of the drive socket. What sometimes happens is the headset top gets pulled up during removal to unscrew the cable ferrule. This stretches the cable outer, when reassembled the inner wo...
- Fri Jun 21, 2013 12:41 am
- Forum: Lambretta Tech
- Topic: Charging
- Replies: 5
- Views: 2666
Re: Charging
Simples, do a search on Wassell DC conversion on here. That's the best way Rick!Ricko wrote:Whats the best way of keeping the battery charged at 12v?....
Cheers all.
Rick
cheers,
Nigel
- Fri May 31, 2013 7:39 pm
- Forum: Lambretta Tech
- Topic: Ron Moss
- Replies: 8
- Views: 2460
Re: Ron Moss
Ron's great to deal with, shame about his exhaust supplier...... 
- Thu May 30, 2013 12:11 pm
- Forum: Lambretta Tech
- Topic: Blowing bulbs
- Replies: 10
- Views: 5889
Re: Blowing bulbs
^ What he saidMonty wrote:I would check the regulator is working correctly, a voltmeter would help, your stator will kick out anything from 8-9 volts at tickover to over 20V at full revs The regulator regulates it lol, test it before and after the regulator, set to AC. check any earths are good
- Tue May 28, 2013 11:01 am
- Forum: Lambretta Tech
- Topic: Blowing bulbs
- Replies: 10
- Views: 5889
Re: Blowing bulbs
My scoot has over the last couple of months and for no obvious reason started to blow headlamp bulbs with worrying regularity. I haven't changed anything which i believe might have influenced this issue however Ive got through so many bulbs recently that I'm starting to think it can't just be down ...
- Fri May 10, 2013 7:29 pm
- Forum: Lambretta Tech
- Topic: sip speedo gear ratio setting??? getting speedo right
- Replies: 18
- Views: 9765
Re: sip speedo gear ratio setting??? getting speedo right
Not a lumpy Schwalbe tyre is it?soulsurfer wrote:.... I'm asking for a mate as his speedo goes up and down like a yoyo and he doesn't have any instructions......
.....I'll get me coat
Wheel circumferences vary quite a bit, don't they? I use 1287 for Bridgestone Hoops with a Ratio of 0.78.
- Sat May 04, 2013 11:35 pm
- Forum: Lambretta Tech
- Topic: Removing exhaust downpipe
- Replies: 6
- Views: 2896
Re: Removing exhaust downpipe
Hmm... me too, spookily enoughTimbo wrote:Remove shock and bump stop. This will allow the cowl to be moved forward, then quite easy, just done it this afternoon...
- Sat May 04, 2013 11:27 pm
- Forum: Lambretta Tech
- Topic: Blown exhaust gasket
- Replies: 19
- Views: 4028
Re: Blown exhaust gasket
said another muppet,,,,Muppet wrote:you muppetsideout wrote:Not a stupid question Ron, that's a GOOD question!OAP wrote:maybe a stupid question but why did you not use the one I supplied with the kit?
Shame I haven't got a good answer......
- Sat May 04, 2013 3:11 pm
- Forum: Lambretta Tech
- Topic: Blown exhaust gasket
- Replies: 19
- Views: 4028
Re: Blown exhaust gasket
Not a stupid question Ron, that's a GOOD question!OAP wrote:maybe a stupid question but why did you not use the one I supplied with the kit?
Shame I haven't got a good answer......
- Sat May 04, 2013 11:45 am
- Forum: Lambretta Tech
- Topic: Blown exhaust gasket
- Replies: 19
- Views: 4028
Re: Blown exhaust gasket
Thanks for the replies chaps, much appreciated as usual! I spend ages flatting the flange to ensure is sits correctly with no high spots, but as Grumpy quite rightly says once it's been heated up a few times and the welding stresses are relieved it's going to move! I think I'm off to the garage for ...