Search found 379 matches

by fluff34567
Sun Oct 28, 2018 12:38 pm
Forum: Lambretta Tech
Topic: Uni rear hub cone
Replies: 8
Views: 1292

Re: Uni rear hub cone

Muppet wrote:uni hub Italian layshaft splines are 4mm inside the keyways with uni hub tightened @120 ftlb
Cheers, mine is about the same. I would have expected the shaft to be flush tbh. The hub has a chamfer so no issues with tightening etc. Oh well more Italian oddity
by fluff34567
Sun Oct 28, 2018 12:23 pm
Forum: Tech FAQ
Topic: Re: 12V DC CONVERSION - HOW TO
Replies: 213
Views: 88779

Re: Re: 12V DC CONVERSION - HOW TO

I have been well happy with my wassell conversion, even fitted a couple of others to friends Scoots . Now want to use one on my Lambretta chopper , can i use this instead of the branded "wassell unit "? https://www.ebay.co.uk/itm/4-Wire-Full-Wave-Motorcycle-Regulator-Rectifier-12V-DC-Bike-Quad-Scoo...
by fluff34567
Tue Sep 11, 2018 5:56 pm
Forum: Lambretta Tech
Topic: Uni rear hub cone
Replies: 8
Views: 1292

Re: Uni rear hub cone

I would have expected it to come through a lot more than it does currently.. it's my first lambretta if you hadn't guessed ;)



Sent from my BND-L21 using Tapatalk

by fluff34567
Mon Sep 10, 2018 3:56 pm
Forum: Lambretta Tech
Topic: Uni rear hub cone
Replies: 8
Views: 1292

Re: Uni rear hub cone

Hi all, Bought a uni rear hub few months ago, went to fit it today and think the supplied cone is incorrect. The shaft splines are about 5mm inside the keyways so only half way through the hub. What cone should I get?? Sent from my BND-L21 using Tapatalk With pic this time https://uploads.tapatalk-...
by fluff34567
Mon Sep 10, 2018 3:55 pm
Forum: Lambretta Tech
Topic: Uni rear hub cone
Replies: 8
Views: 1292

Uni rear hub cone

Hi all,

Bought a uni rear hub few months ago, went to fit it today and think the supplied cone is incorrect.

The shaft splines are about 5mm inside the keyways so only half way through the hub.

What cone should I get??





Sent from my BND-L21 using Tapatalk

by fluff34567
Sun Sep 09, 2018 8:43 am
Forum: Tech FAQ
Topic: Standard series 3 TV175 squish......
Replies: 8
Views: 1110

Re: Standard series 3 TV175 squish......

1.5 packer but 1.0 has been removed from the casing so it's the same as having a standard gasket on a standard case. Port timing comes into play here if adjusting the base thickness. No head gasket used. Depends who you speak to, stickys says 1.2 - 1.5 that's from MB I believe, others say max 1.75. ...
by fluff34567
Sat Sep 08, 2018 3:32 pm
Forum: Tech FAQ
Topic: Standard series 3 TV175 squish......
Replies: 8
Views: 1110

Re: Standard series 3 TV175 squish......

Closure... Port timing was good and after speaking with few tuners appears head is bit of a known issue. Got it down to 1.7mm after a quick skim

Sent from my BND-L21 using Tapatalk

by fluff34567
Sat Sep 08, 2018 3:30 pm
Forum: Lambretta Tech
Topic: Chain tension and scootopia chain
Replies: 3
Views: 841

Re: Chain tension and scootopia chain

Cheers Adam, went with a bit of play and will check after a while. I used the old chain as it's not really worn but unknown to me. The scootopia chain was very tight, I had difficulty to install the clutch. Maybe just a bad one. Sprockets are the right combination btw Sent from my BND-L21 using Tapa...
by fluff34567
Thu Sep 06, 2018 8:17 pm
Forum: Lambretta Tech
Topic: Chain tension and scootopia chain
Replies: 3
Views: 841

Chain tension and scootopia chain

Stickys says 6mm up and down movement,. Is it 6mm up and 6mm down giving a total movement of 12mm or a total of 6mm as it can be taken both ways. Next. I have a new scootopia chain and it's extremely tight so much so I took it off and put in the older Regina chain. Anyone else experienced that with...
by fluff34567
Mon Sep 03, 2018 8:49 pm
Forum: General Scooter Chat
Topic: Anyone burn carbon out of two cycle mufflers?
Replies: 4
Views: 660

Re: Anyone burn carbon out of two cycle mufflers?

You get the same result by plugging one end and pouring in some industrial cleaner or caustic soda and leaving it to soak for a while. I used industrial cleaner overnight to break down the oil and then all the carbon comes out at the same time. Looks new inside Sent from my BND-L21 using Tapatalk