Search found 71 matches
- Mon May 12, 2014 9:24 pm
- Forum: Tech FAQ
- Topic: Malossi 166 alternative piston?
- Replies: 12
- Views: 4651
Re: Malossi 166 alternative piston?
There is a 64mm piston that will go in from a Kawasaki
- Mon May 12, 2014 9:21 pm
- Forum: Tech FAQ
- Topic: Gordon Jennings 2t tuning book down load
- Replies: 1
- Views: 2000
Re: Gordon Jennings 2t tuning book down load
If you have the tail pipe starting in the Center section ie the largest Dia of the exhaust pipe, this is where the gas pressure is at it's lowest! If you fit the tale pipe at the end of the rear cone it is at the highest pressure point. By using the tail pipe start point in the Center section it als...
- Mon May 12, 2014 9:07 pm
- Forum: Tech FAQ
- Topic: OEM BRAKE SPECS FOR LAMBRETTA
- Replies: 2
- Views: 2340
Re: OEM BRAKE SPECS FOR LAMBRETTA
Brake drum diameter is 152mm x 25mm wide shoe. The jockey boxenshop is 150 Dia
- Mon May 12, 2014 8:29 pm
- Forum: Lambretta Tech
- Topic: Cyclone mk 3 f@@ked
- Replies: 19
- Views: 8318
Re: Cyclone mk 3 f@@ked
Boo what is the power output of your motor? Is it TS1 or RB based?
- Mon May 12, 2014 8:23 pm
- Forum: Lambretta Tech
- Topic: Supermonza / TZR 125 intake rubber + reed spacer
- Replies: 22
- Views: 8777
Re: Supermonza / TZR 125 intake rubber + reed spacer
We used a Yamaha 250 motocross inlet rubber 4V3 & modified the rubber. This also sits the carb more upright. We are using a 39mm Dellorto.
- Fri Dec 06, 2013 12:49 am
- Forum: Lambretta Tech
- Topic: Jockey Boxenstop rear brake
- Replies: 9
- Views: 5493
Re: Jockey Boxenstop rear brake
Hi Syd,sydduckett wrote:Does anyone know who has a Jockey rear brake for an Li in stock? they only seem to have the GP type in stock. Can't find any other dealers stocking them.
Thanks
Sef
I have 3 sets in stock at the moment give me a call on 07794 003276 Taffspeed or text me.
- Sat Nov 09, 2013 4:18 pm
- Forum: Lambretta Tech
- Topic: UPDATE ON Version v4.11 of the Gearbox visualiser
- Replies: 0
- Views: 2042
UPDATE ON Version v4.11 of the Gearbox visualiser
I asked Tony if he could include the facility of custom gearbox sets again as per V3.30. Well Tony has now done this latest version to included an update to enter gearbox ratio permutations that you dream up & be able to save & compare it to other set ups! Version v4.11 of the visualiser in ...
- Wed Nov 06, 2013 2:20 am
- Forum: Liquid Cooled, Motorcycle Engine & Automatics Section
- Topic: water cooling a standard head.
- Replies: 15
- Views: 9942
Re: water cooling a standard head.
Have a look at Duncan Cully's Vespa PX220-LC (221cc) Revamp 2013 in my photo albums - Ian Frankland on Facebook or give me a call if you need info also we do cast LC head blanks for machining if you need them?
- Mon Jul 29, 2013 9:07 pm
- Forum: Lambretta Tech
- Topic: 5 speed fouling kickstart
- Replies: 12
- Views: 3780
Re: 5 speed fouling kickstart
As Dave said, check the reference pin isn't worn, this can make quite a difference if it is! Some kickstart shafts are not retained well from the outside, AF Rayspeed do a new shim & starred circlip which helps keep the shaft from moving inwards & hence then rubbing the clutch top bevel plat...
- Mon Jul 29, 2013 7:20 pm
- Forum: Lambretta Tech
- Topic: Cyclone 5 speed cluster update!
- Replies: 3
- Views: 2186
Cyclone 5 speed cluster update!
As those of you who had the ordered the 2nd batch of Cyclone 5 gear sets will know RLC recalled all the clusters as DRT had altered the interference fit in an attempt to improve on the power capability of the loose gears, this has resulted in a few cases of split gears & they in turn spinning on...