Search found 465 matches
- Sun Aug 01, 2021 1:36 am
- Forum: Lambretta Tech
- Topic: Why?????,this is doing my head in.....
- Replies: 17
- Views: 20146
Re: Why?????,this is doing my head in.....
I have had two Scootopia filters where the paper element was packed too tightly causing the exact problem you are having. Check you filters against a know good one, you'll see the difference.
- Fri May 28, 2021 10:02 pm
- Forum: Lambretta Tech
- Topic: Lambretta Li150 Vibration/Noise at high rpm
- Replies: 3
- Views: 1761
Re: Lambretta Li150 Vibration/Noise at high rpm
Put you hand on the rear shock spring and see if that's it. Easy stuff first.
- Fri May 28, 2021 10:00 pm
- Forum: Lambretta Tech
- Topic: Nightmare of a day.....
- Replies: 13
- Views: 9892
Re: Nightmare of a day.....
As an aside, why didn't you just do a 12v light conversion on the points set up? Would have been loads cheaper and easier.
- Fri May 21, 2021 10:16 pm
- Forum: Lambretta Tech
- Topic: Standard exhaust
- Replies: 8
- Views: 3919
Re: Standard exhaust
Find an exhaust gasket that matches the exhaust port(or even use a piece of paper to take a pattern) then put it onto the exhaust flange to see if it is the same. If it's not, get the file out and make it the same. You'll know you have no obstruction then.
- Sun Jun 28, 2020 3:23 am
- Forum: Lambretta Tech
- Topic: Sealed bearing on crankcase side?
- Replies: 8
- Views: 4351
Re: Sealed bearing on crankcase side?
You say the "bearing is pregreased" How do you know the manufacturer actually put grease in the bearing in your engine without removing the seal/cover? Manufacturers are not perfect and make mistakes all the time. I have opened sealed bearings only to find no grease had be applied to the b...
- Mon May 27, 2019 4:57 am
- Forum: General Scooter Chat
- Topic: Crikey its quiet in here ..iet in here...in here... here..
- Replies: 79
- Views: 94136
Re: Crikey its quiet in here ..iet in here...in here... here..
So 39mm from the top of the exhaust port to the the top of the cylinder isn't optimum any more?
- Sun May 19, 2019 2:32 am
- Forum: Lambretta Tech
- Topic: Help Understanding stator test results.
- Replies: 7
- Views: 3931
Re: Help Understanding stator test results.
Just to throw this out there... Is the magnetism good in the BGM flywheel? I only ask as I did a comparison between an indian flywheel and a BGM flywheel and the Indian flywheel won hands down. Using a spark plug gap tester, the indian flywheel put out a lot bigger spark also. Stands to reason if th...
- Mon Jul 30, 2018 2:39 am
- Forum: Lambretta Tech
- Topic: Gear Compatibility
- Replies: 23
- Views: 8530
Re: Gear Compatibility
Some gears gears just won't fit together correctly, that's all there is to it.
- Mon Jul 30, 2018 2:29 am
- Forum: Lambretta Tech
- Topic: Gear Compatibility
- Replies: 23
- Views: 8530
Re: Gear Compatibility
Some gears gears just won't fit together correctly, that's all there is to it. If you would like to count gears and make up gearboxes, come have at it.
- Mon Jul 30, 2018 2:03 am
- Forum: Lambretta Tech
- Topic: New 185cc engine won't start or run
- Replies: 29
- Views: 11841