Search found 74 matches

by Mrnice71
Fri Jun 14, 2019 8:32 pm
Forum: Lambretta Tech
Topic: ST90 vs SAE30
Replies: 9
Views: 516

Re: ST90 vs SAE30

Firstly readspeed recommend Putoline SAE 90 , its says on the bottle special lambretta gear oil and l have found this to be by far the best gear oil , also make sure u give the plates a good soak in the oil preferably over nite , and ruff the steels also . What springs are u using ?
by Mrnice71
Sun Jun 09, 2019 11:21 pm
Forum: General Scooter Chat
Topic: Tyre Choices
Replies: 18
Views: 677

Re: Tyre Choices

Dunlop scootersmarts
by Mrnice71
Thu Jun 06, 2019 4:19 pm
Forum: Lambretta Tech
Topic: Joint
Replies: 7
Views: 446

Re: Joint

MB scooters do one in stainless , but if your fuel tap is not straight they will break . Guess your using a big carb on the left hand side
by Mrnice71
Mon May 20, 2019 8:20 pm
Forum: Lambretta Tech
Topic: Readspeed Lukas CDI
Replies: 6
Views: 429

Re: Readspeed Lukas CDI

Ok cheers guys
by Mrnice71
Sun May 19, 2019 7:04 pm
Forum: Lambretta Tech
Topic: Readspeed Lukas CDI
Replies: 6
Views: 429

Re: Readspeed Lukas CDI

Dont quite understand you there Paul ? Do you mean regulate the power coming from the CDI unit ?
by Mrnice71
Sun May 19, 2019 1:53 pm
Forum: Lambretta Tech
Topic: Readspeed Lukas CDI
Replies: 6
Views: 429

Readspeed Lukas CDI

Do you run the Readspeed Lukas CDI with or without a voltage regulator on A/C ? Cheers
by Mrnice71
Fri May 17, 2019 5:38 pm
Forum: Lambretta Tech
Topic: Wits end ...and past it
Replies: 22
Views: 903

Re: Wits end ...and past it

l would speak to Mark as that bearing may use a different seal , the inner lip sits down and some hub bearings can have a sharp leading edge , also are you using seal grease on assembly as a seal fitted dry will quickly fail as the bearing goes tight once the seal is fitted
by Mrnice71
Fri May 17, 2019 2:29 pm
Forum: Lambretta Tech
Topic: Wits end ...and past it
Replies: 22
Views: 903

Re: Wits end ...and past it

Just because its pre-fitted doesn't mean its fitted correctly , buy a new seal & fit it yourself
by Mrnice71
Fri May 17, 2019 11:21 am
Forum: Lambretta Tech
Topic: Wits end ...and past it
Replies: 22
Views: 903

Re: Wits end ...and past it

The MB hub bearings are known to be crap l would recommend RIV or Casa , what make of seal is it ? l only use Rolf , l can never even fit the pattern ones without damaging them and warm them up a bit when fitting and lots of seal grease
by Mrnice71
Thu May 09, 2019 12:25 pm
Forum: Lambretta Tech
Topic: Jetting
Replies: 11
Views: 755

Re: Jetting

l run a 3.50 mm float valve jet on a 30 mm dellorto flatslide , put the 3.00mm back in or you will have fuel starvation issues .
Air filters are restrictive which will richen up jetting , so try a 135 main jet , let us know how you get on .