Search found 366 matches

by fluff34567
Tue Mar 19, 2019 8:10 pm
Forum: Wanted
Topic: Tv175 S3 barrel and head
Replies: 0
Views: 46

Tv175 S3 barrel and head

Looking for a genuine series 3 Tv175 barrel head and Inlet/ carb if you have it as a job lot.

Let me know what you have.
by fluff34567
Mon Mar 18, 2019 11:34 am
Forum: Lambretta Tech
Topic: S3 layshaft slop
Replies: 17
Views: 672

Re: S3 layshaft slop

This other Spanish endplate bush is 24.3 and a good fit with bearing and layshaft so it looks like anything under 24 is worn and could lead to play on the wheel Sent from my SM-A320FL using Tapatalk Sorry, If I'm being thick, but I presume you're measuring the ID of the bearing track? Assuming the ...
by fluff34567
Mon Mar 18, 2019 11:27 am
Forum: Lambretta Tech
Topic: Uni Hub 8 or 11 degrees?
Replies: 0
Views: 96

Uni Hub 8 or 11 degrees?

As per title. Does anyone know the angle of the uni hubs? I couldnt find anything online.
by fluff34567
Sun Mar 17, 2019 8:18 pm
Forum: Lambretta Tech
Topic: S3 layshaft slop
Replies: 17
Views: 672

Re: S3 layshaft slop

Cheers Gary, just saw the reply now. My shafts are marginally smaller but the bush Is also smaller.
by fluff34567
Sat Mar 16, 2019 10:40 pm
Forum: Lambretta Tech
Topic: S3 layshaft slop
Replies: 17
Views: 672

Re: S3 layshaft slop

New replacement bush is too big.. Typical
by fluff34567
Sat Mar 16, 2019 8:07 pm
Forum: Lambretta Tech
Topic: S3 layshaft slop
Replies: 17
Views: 672

Re: S3 layshaft slop

As Gary has suggexyed/suspected, the new bush/bearing cage is a big bigger compared to an original unit. Would anyone have an MB layshaft and a good set of digital verniers or a micrometer and can measure the end of the layshaft for me so I can compare to mine before I lay out £150 for a new one.
by fluff34567
Sat Mar 16, 2019 6:14 pm
Forum: Lambretta Tech
Topic: S3 layshaft slop
Replies: 17
Views: 672

Re: S3 layshaft slop

So side case off and there is some movement of the shaft at the end plate needle cage.. That's a bit s**t as I had replaced the needle roller and the holder during the rebuild.. It could also be the shaft.
by fluff34567
Sat Mar 16, 2019 5:39 pm
Forum: Lambretta Tech
Topic: S3 layshaft slop
Replies: 17
Views: 672

Re: S3 layshaft slop

Will start taking the side case off and see what's going on inside. Strangely there is more movement when on the stand compared to rear wheel off the ground.
by fluff34567
Sat Mar 16, 2019 3:56 pm
Forum: Lambretta Tech
Topic: S3 layshaft slop
Replies: 17
Views: 672

S3 layshaft slop

Newly rebuilt engine, zero miles. new MB hub bearing and new SKF end plate bearing. Gearbox shimming close to the minimum gap.. Can't remember exact figure. When on the centre stand I can move the rear wheel slightly and hear a knock which I guess is shaft in the end plate. Hub correctly torqued.. G...
by fluff34567
Wed Mar 13, 2019 10:20 am
Forum: Lambretta Tech
Topic: Grey rubber trim, black kickstart/stand feet?
Replies: 2
Views: 218

Re: Grey rubber trim, black kickstart/stand feet?

Cheers pretty much confirmed my original Thoughts